Skil 1525 Instrucciones página 7

Safety support L 4
●
- protects workpiece from damage when tool is put
aside
- will automatically fold backwards when planing
Safety bracket F 3
●
- prevents contact with rotating knife
- opens automatically when planing rabbets
Operating the tool
●
- adjust planing depth
- place tool on workpiece
! ensure that only the front shoe rests on the
workpiece and that the knives do not touch it
- switch on the tool by first pressing knob M 2 (=
safety switch which cannot be locked) and then
pulling trigger N 2
! before the knives reach the workpiece, the tool
should run at full speed
- hold the tool firmly with both hands and guide it
forward in a continuous stroke
- use the tool with its base-plate on the workpiece
- do not tilt the tool in order to avoid unwanted planing
marks
- keep the ventilation slots uncovered
! before switching off the tool, you should lift it
from the workpiece
- switch off the tool by releasing trigger N
Planing rabbets
●
- select required planing depth
- select rabbeting depth by using rabbeting depth
adjuster P 2
- adjust rabbeting width by using rip fence Q 3
- place tool on workpiece
- start planing
- maximum rabbeting width 82 mm
- maximum rabbeting depth 24 mm
APPLICATION ADVICE
For chamfering edges use the V-groove in the front
●
shoe 5
- turn knob H to select required depth
- always test out first on a piece of scrap material
For planing a considerable amount of beams with a
●
uniform planing depth a plane stand is advised for
stationary use (SKIL accessory 2610387872)
WHEN USING PLANE STAND:
! switch off the tool and disconnect the plug before
using plane stand
- the plane stand is equipped with a switch clamp
allowing the plane to operate independently
- switch on the plane by first pressing knob M 2 and
then pushing the clamp over switch N 2
- in order to switch off the plane, pull the cord attached
to the clamp
- the knife protection guard prevents contact with
rotating knife; it will open automatically when pushed
by workpiece
! when planing short, narrow workpieces, use a
pushing device
For more tips see www.skileurope.com
●
GUARANTEE / ENVIRONMENT
Always keep tool and cord clean (especially the
●
ventilation slots)
! disconnect the plug before cleaning
This SKIL product is guaranteed in accordance with
●
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
In case of a complaint, send the tool undismantled
●
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
Do not dispose of electric tools, accessories and
●
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
F
Rabot
INTRODUCTION
Cet outil est conçu pour le rabotage des matériaux en
●
bois, tels que des poutres et des plances; il est
également approprié pour chanfreiner et pour faire des
feuillures
Lisez et conservez ce manuel d'instruction
●
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 2 3
A Rangement pour la clé
B Boulon de fixation
C Clé
D Elément de serrage
E Arbre porte-couteaux
F Patte de sécurité
G Vis de l'arbre porte-couteaux
H Bouton de réglage de la profondeur de rabotage
J Échelle de la profondeur de rabotage
K Sortie poussière
L Appui de sécurité
M Interrupteur de sécurité
N Interrupteur marche/arrêt
P Guide de profondeur de feuillure
Q Guide parallèle
7
1525