Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
maximum distance of 5 mm between the grinding disc and the
spark defletor (3).
•
Now secure the workpiece supports, ensuring the here too
there is a maximum distance of 3 mm between the grinding disc
and the support. [F1]
Assembly instructions
Mounting spark deflectors (3)
•
Mount the left and right spark deflectors (3) with eyeshield
(7) to the special hole on the disk protector (4) using screws (10)
washers (11) and nuts (12).
•
Make sure that spark deflectors (3) with eyeshield (7) are
firmly in place.
WARNING
To prevent personal injury, never operate the bench grinder
unless the safety eyeshields (7) and spark deflectors (3) are
properly installed and in place.
Mounting workpiece supports (2)
•
Mount the two workpiece supports (2) using their knobs (6),
washers and screws for workpiece support.
•
Before tightening the bolts, adjust the gap between the
grinding disc (5) and the workpiece support (2) to a optimal gap
of 1.6 mm.
•
Tighten securely.
Initial operation
Always use the correct supply voltage: the power supply voltage
must match the information quoted on the tool identification
plate.
Switching On/Off
Switching On
•
Press On/Off switch (1) and put it on the «I» position.
Switching Off
•
Press On/Off switch (1) and put it on the «O» position.
[F3]
Operating instruction
WARNING
Always wear safety goggles or safety glasses with side shields
during power tool operation or when blowing dust. If operation
is dusty, wear a dust mask.
To be efficient and work as designed, your tools should be kept
sharp. Dull tools can and will cause accidents.
Never sharpen or grind anything made of aluminium.
Grinders remove material rapidly so pressure is the key to
efficient grinding.
Grinding disc (5) replacement
If you must replace a grinding disc (5), be sure to obtain one with
a safe rated speed at least as high as the "no load speed" RPM
[F2]
marked on the data plate of the grinder. Only grinding discs
must be used which carry information about the maker, kind of
bond, dimensions and permissible rotary speed.
To replace the grinding disc (5):
•
•
side and a counterclockwise direction for the right side.
•
[F4]
To install a new grinding disc (5):
•
•
properly seated on the spindle shaft (8).
Maintenance and storage
Before any work on the machine itself, pull the mains plug.
•
cleaned. Regular cleaning and maintenance of the appliance
will ensure efficiency and prolong the life of your tool.
•
and testing procedures, the repair should be carried out by an
authorized IVT customer service.
•
safe working condition.
•
•
manufacturer may cause poor fit and possible injury.
•
from any flammable material.
•
•
parts and beneath the grinder frequently.
•
screws, nuts, and bolts for tightness.
•
To keep the loss to a minimum and to prevent tool overheating,
use an extension cord that is heavy enough to carry the current
the tool will draw.
11
Instruction manual
WARNING
Remove the disc protector (4) by loosening its screws (9).
Loosen the disc nut (15) in a clockwise direction for the left
Remove the outer flange (14) and grinding disc (5).
Reverse the above procedure.
Be sure the grinding disc (5) and outer flange (14) are
CAUTION
Always keep the tool and the ventilation slots (if present)
If the tool should fail despite the rigorous manufacturing
Keep all nuts, bolts, and screws tight, to be sure the tool is in
Replace worn or damaged parts for safety.
Use only original spare parts. Parts not produced by
Store the tool in a dry room out of reach of kids and away
Never wet the device or spray water on it!
Keep the bench grinder clean. Remove dust from working
Make sure the bench grinder operates properly. Check
The use of any extension cord will cause some loss of power.
EN
Publicidad
Tabla de contenido
