KN04-00047A (Rev.1.6)
◈ Information
This Installation Guide includes a brief outline of information necessary for product
installation. For more detailed installation information, please refer to the user manual in the
enclosed CD. The contents of the CD include the following.
1. Manual: User Manual, Code Chart, Control Commands
2. Drivers: Windows Drivers, OPOS Drivers
3. Utilities: a Logo download tool and a virtual memory switch control tool
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Components
SRP-350plusIIC
SRP-350plusIIA
USB A-A JACK
◈ Connecting the cables
1. Turn off the printer and the host ECR (host computer).
2. Plug the power cord into the Adaptor, and then plug the Adaptor into the power connector
of the printer.
3. Check the interface cable (Serial, Parallel, USB, or Ethernet), and connect the interface
connector cable accordingly.
4. Plug the drawer kick-out cable into the drawer kick-out connector on the printer.
※ Do not use an adapter that was not supplied with the printer.
Interface connector
Interface cable
(Serial/Parallel/USB/Ethernet)
◈ Installing the Paper Roll
◈ Using the Operation Panel
• POWER (LED)
When turning on the power, a green LED will be lit.
• ERROR (LED)
When an error occurs, a red LED will be lit.
(e.g. no paper, cover ajar, etc.)
• PAPER (LED)
Red LED will be lit when the paper roll is running low. The LED blinks
when the printer is in self-test standby mode or macro execution standby
mode.
• FEED (Button)
Press the FEED button once to discharge extra paper. Holding down the
FEED button will discharge paper continuously until the button is
released.
THERMAL PRINTER SRP-350/352plusIIA&C
Cable cover
Paper Roll
Procuct Installation CD
Procuct Installation CD
Procuct Installation CD
CD
Installation Guide
AC/DC Adaptor
Power cord
Drawer kick-out connector
Power connector
Adaptor
Power cord
Drawer kick-
out cable
1. Open the paper roll cover by pressing the cover-
open button.
2. Insert a new paper roll, making sure to align it
properly.
3. Pull out a small amount of paper, and close the
cover.
※ Note
When closing the cover, press down on the center
of the cover to ensure that the paper is in contact
with the roller.
Printing quality may not be optimum if
recommended paper is not used.
(Refer to the User's Manual.)
Printer Installation Guide
◈ Setting the DIP Switches
Changing Dip Switch settings must be done when the printer is off. Any changes done while
the printer is on will not be processed.
1. Serial Interface
• DIP Switch 1
SW
Function
1-1
Auto Line Feed
1-2
Flow Control
1-3
Data Length
1-4
Parity Check
1-5
Parity Selection
1-6
1-7
Baud Rate Selection (bps)
1-8
• DIP Switch 2
SW
Function
2-1
Auto cutter control
2-2
Internal bell control
2-3
Auto Cutter
2-4
Reserved
2-5
Print Density
2-6
2-7
Near-End Sensor Status
2-8
External buzzer control
2. Parallel / USB Interface
• DIP Switch 1
SW
Function
1-1
Auto Line Feed
1-2
Reserved
1-3
Reserved
1-4
Reserved
1-5
Reserved
1-6
Reserved
1-7
Reserved
1-8
Reserved
• DIP Switch 2
SW
Function
2-1
Auto cutter control
2-2
Internal bell control
2-3
Auto Cutter
2-4
Reserved
2-5
Print Density
2-6
2-7
Near-End Sensor Status
2-8
External buzzer control
• Table 1 – Baud rate (bps) Selection
Transmission Speed
2400
4800
9600
19200
38400
57600
115200
• Table 2 – Print Density Selection
Print Density
1 (Light)
2
3
4 (Dark)
◈ Self-Test
1. Make sure the paper roll has been installed properly.
2. Turn on the power while holding down the FEED button. The self-test begins.
3. The self-test prints the current printer status, providing the control ROM version and the
DIP switch setting.
4. After printing the current printer status, self-test printing will print the following, and
pause. (The PAPER LED light blinks.).
PLEASE PRESS THE FEED BUTTON.
5. Press the FEED button to continue printing. The printer prints a pattern using the built-in
character set.
6. The self-test automatically ends and cuts the paper after printing the following.
7. After the self-test is complete, the printer returns to normal on-line status.
※ Note
The self-test lets you know if your printer is operating properly. It checks the print quality,
ROM version, and DIP switch settings.
ON
OFF
Enable
Disable
XON/XOFF
DTR/DSR
7bits
8bits
Yes
EVEN
ODD
Refer to the following table 1
ON
OFF
Full cut
Partial cut
Internal bell disable
Internal bell enable
Auto cutter disable
Auto cutter enable
-
Refer to the following table 2
Disable
Enable
External buzzer
External buzzer
enable
disable
ON
OFF
Enable
Disable
-
-
-
-
-
-
-
ON
OFF
Full cut
Partial cut
Internal bell disable
Internal bell enable
Auto cutter disable
Auto cutter enable
-
Refer to the following table 2
Disable
Enable
External buzzer
External buzzer
enable
disable
1-6
1-7
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
2-5
2-6
ON
ON
OFF
OFF
ON
OFF
OFF
ON
SELF-TEST PRINTING.
*** COMPLETED ***
Default
OFF
OFF
OFF
No
OFF
OFF
OFF
ON
OFF
Default
OFF
OFF
OFF
-
OFF
OFF
OFF
OFF
OFF
Default
OFF
-
OFF
-
OFF
-
OFF
-
OFF
-
OFF
-
ON
-
OFF
Default
OFF
OFF
OFF
-
OFF
OFF
OFF
OFF
OFF
1-8
Default
OFF
ON
OFF
OFF
9600
ON
ON
ON
Default
2