Vimar Giotto 6328 Manual De Instrucciones página 5

5
4
3
2
1
6328, 6328/C, 6328/CD
Association of call push-button from the entrance panel
To associate the entrance panel push-button with which to call and
switch on the monitor, operate on contacts 4 and 5: contact 4 for the
right hand panel push-button or 1° push-button and contact 5 for the
left hand push-button or 2° push-button. Inserting the jumpers the
call is excluded, removing them the call and the monitor activation
is enabled.
1 2 3 4 5
D0 MONITOR
ID 0
n°1
ID 1
n°2
n°3
4 5
n°4
VIDEO SIGNAL STABILISATION
If an image on the monitor is misshaped, displace jumper, placed on
the monitor fixing plate (R684, R682), to one of the following alterna-
tive positions "B" or "C".
On installations where several monitors
are connected in series between them,
place only the jumper of last monitor
to the "B" or "C" position and kepp the
other jumpers of other monitors in the
"A" position.
On installations with more monitors con-
nected in star configuration, place the
jumper to the "B" or "C" position only on
the monitor with misshaped image.
MONITOR INSTALLATION (FIG. 1-2, Page 11)
- The monitor should be installed far away from sources of light, heat
and electrical disturbances.
- Fix metal hooking plate to the wall with fixing screws supplied,
keeping top of panel at 1,40 m. from ground level.
- A drilling is forseen in order to fix the plate to a module flush-
mounted back box.
- Carry out connections on monitor terminal block following the dia-
grams.
- Hook the monitor following the arrow 1 and 2 direction .
- To remove the monitor from the hooking plate, operate with a
screwdriver on the security lock and remove it following the arrows
1 and 2 in the opposite direction.
The monitor can be transformed into desk-top version by using the
proper conversion kit type 661A (Fig. 4, page 11).
CH2
CH1
APERTURA SERRATURA SEMPRE
LOCK RELEASE ALWAYS
CH2
APERTURA SERRATURA DOPO CHIAMATA
CH1
LOCK RELEASE AFTER CALL
CONNECTIONS
The two connecting wires between power supply and monitor can
be inverted.
- The advised section for the two conductors is of 0,75 mm² (twisted
pair). The following features cannot be guaranted if the section is
different.
- The installation is guaranted for a good operation with 100 m max-
imum distance from the power supply to the monitor.
- In any case the maximum distance between the camera and the
monitor must not exceed 120 m.
- The electric lock connected to the installation must have a maxi-
mum of 1A power consumption with 12V voltage.
- Humming sounds or electrical discharges may affect the appliance
good operation.
Operating dwell time:
The monitor, camera, door lock and auxiliary services mut operate
according to the following intermittent cycles.
Monitor and camera activation cycle:
max. 90 seconds activated, 90 seconds deactivated
Door lock cycle:
max. 30 seconds activated, 150 seconds deactivated
Auxiliary service cycle:
max. 90 seconds activated, 90 seconds deactivated
Installation rules
Installation should be carried out by qualified personnel in
compliance with the current regulations regarding the installation of
electrical equipment in the country where the products are installed.
Conformity
EMC directive
Standards EN 61000-6-1 and EN 61000-6-3.
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may
contain traces of lead.
WEEE - Information for users
If the crossed-out bin symbol appears on the equipment or
packaging, this means the product must not be included
with other general waste at the end of its working life. The
user must take the worn product to a sorted waste center,
or return it to the retailer when purchasing a new one. Products
for disposal can be consigned free of charge (without any new
purchase obligation) to retailers with a sales area of at least 400m
if they measure less than 25cm. An efficient sorted waste collection
for the environmentally friendly disposal of the used device, or its
subsequent recycling, helps avoid the potential negative effects on
the environment and people's health, and encourages the re-use
and/or recycling of the construction materials.
EN
,
2
5