IVT RHM-1000-RC Manual De Instrucciones página 10

Instruction manual
ATTENTION! DANGER OF ELECTRIC
SHOCK!
EN
Consider working area environment. Do not expose
power tools to rain. Do not use power tools in damp
or wet locations. Keep work area well lit and dry. Try
to prevent the device from getting wet or being
exposed to humidity. Do not leave it outside
overnight. Water entering a power tool will increase
the risk of electric shock.
∙
The power supply cable should be checked
regularly and, before using it, make sure the cable is
not damaged or worn out. If the cable is not in good
condition, do not use the appliance; take it to an
authorized service center.
∙
When tool is used outdoor, only use an extension
cable that is suitable for outdoor use and which is
marked for this specific use. Keep it away from the
working area, from damp, wet or oily surfaces and away
from heat and flammable materials.
∙
Avoid any accidental starting: make sure that the
power switch (if present) is in the «off» position, before
plugging the tool in.
∙
Remove adjusting keys or wrenches before turning
the tool on.
∙
Do not use the tool if the switch does not turn the
tool on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
WARNING! During the use of certain
power tools, some dust containing
chemicals known to cause cancer,
may occur.
Some of these chemicals are: lead from lead based
paints, crystalline silica from bricks and cement and
other masonry products, arsenic and chromium from
chemically treated lumber and other dangerous
products. If dust is present, your risk from these
exposures varies, depending on how often you do this
type of work. To reduce your exposure to these
chemicals, any time you do pulverulent operations,
work in a well ventilated area and work with
approved safety equipment, such as dust masks
that are specially designed to filter out microscopic
particles.
∙ If the appliance strikes a foreign body, examine the
device for signs of damage and carry out any necessary
repairs before restarting and continuing to work.
∙ If the appliance starts to vibrate abnormally, turn
it off and check for the cause immediately. Vibration is
generally a warning of trouble.
∙
Always switch off the appliance and wait until
the device completely stops whenever you leave
the machine, before
before changing accessories, checking, cleaning,
troubleshooting or working on the appliance.
∙
It is forbidden to move or modify any of the internal
parts of the device.
Specific safety rules
∙ Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool
"live" and shock the operator.
∙ Wear ear protectors when using the tool for
extended periods. Prolonged exposure to high intensity
noise can cause hearing loss.
∙ Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses are NOT
safety glasses. It is also highly recommended that you
wear a dust mask and thickly padded gloves.
∙ Be sure the bit is secured in place before operation.
∙ Under normal operation, the tool is designed to
produce vibration. The screws can come loose easily,
causing a breakdown or accident. Check tightness of
screws carefully before operation.
∙ In cold weather or when the tool has not been
used for a long time, let the tool warm up for a while
by operating it under no load. This will loosen up the
lubrication. Without
operation is difficult.
∙
Always be sure you have a firm footing. Be sure no
one is below when using the tool in high locations.
∙
Hold the tool firmly with both hands.
∙ Keep hands away from moving parts.
∙ Do not leave the tool running. Operate the tool only
when hand-held.
∙ Do not point the tool at any one in the area when
operating. The bit could fly out and injure someone
seriously.
∙ Do not touch the bit or parts close to the bit
immediately after operation; they may be extremely hot
and could burn your skin.
∙ Some materials contain chemicals which may be
toxic. Take caution to prevent dust inhalation and skin
contact.
∙
Store the device where it is inaccessible to children.
10
carrying out maintenance,
proper warm-up, hammering