Simu HZ Manual De Instrucciones página 4

2 Test
For operation 2.1, work with only one unprogrammed receiver connected to the electrical system.
2.1
ON
2.2
a
>>
b
>> >>
Setting the motor limit switches
3
- To set the motor limit switches, use keys Up and Down of the transmitter to control the motor. (refer to the instructions supplied with the
motor).
If you do not want to programme the transmitter that has been used for the test and for setting the limit swit-
ches later on as the receiver control point, switch off the power supply of the receiver for two seconds and then
perform operation 2.1 with a new transmitter before you perform operation 4.
Location of the Prog key on Hz transmitter:
i
For programming the sequential transmitter, refer to
the instructions supplied with the transmitter.
Programming the first transmitter with the Hz receiver
4
>>
PROG 1s
Programming a new transmitter
5
>>
PROG 3s
>>
PROG 1s
- For group control with the new transmitter, perform operations 5.1 and 5.2 for each receiver of the relevant group.
- For general control with the new transmitter, perform operations 5.1 and 5.2 for each receiver of the installation.
- To delete an transmitter from the memory of a receiver, perform operations 5.1 with a programmed transmitter and 5.2 with the transmitter to be deleted.
6 Cancelling programming
OFF ON
6.1 2s 6.2
If you switch on/off the power to several receivers, they will all be in the cancellation mode. That is why you must "drop" all the recei-
vers that are not to be cancelled by controlling them from their individual control transmitter.
>>
PROG 7s
Warning: after stage 6.4, if nothing is done within 2 minutes, the motor will run again for 5 seconds in the direc-
tion opposite to that of 6.4.
>>>
>2s
>> >>
- Press the "PROG" key for approximately one second. The motor will run for half a second in one
direction and then in the other. Your transmitter is now programmed to control the Hz receiver
in stable mode. All transmitters that control only one receiver may be used in §5 as an indivi-
dual control for programming new transmitters.
5.1 - Open the memory of the receiver from the individual control transmitter:
- Press the "PROG" key of the individual control transmitter for approximately 3 seconds. The motor will run
for half a second in one direction and then in the other.
5.2 - Validate the operation from the new transmitter to be programmed:
- Press the "PROG" key of the new transmitter for approximately one second. The motor will run for half a
second in one direction and then in the other.
6.1 - Switch off the power supply to the receiver for 2 seconds.
6.2 - Switch the power to the receiver back on for 7 seconds.
6.3 - Switch off the power supply to the receiver for 2 seconds.
6.4 - Switch the power to the receiver back on. The motor will run for 5 seconds.
OFF ON
7s 6.3 2s 6.4
6.5 - Confirm the cancellation of the affected receiver from the individual control transmitter:
- Press the Prog key of the individual control transmitter for more than 7 seconds. The motor will first
>>
run for half a second in one direction and then in the other. A few seconds later, it will run again in
the two directions.
- Switch on the receiver. The motor will run for half a second in one direc-
tion and then in the other.
- Then simultaneously press the Up and Down keys of a transmitter. The
motor will run for half a second in one direction and then in the other.
The transmitter now controls the receiver in unstable mode for opera-
tions 2.2, 3 and 4.
Checking the motor rotation direction:
a - If the shutter goes up, move to the next step.
b - If the shutter goes down, reverse the rotation direction by
pressing STOP for at least two seconds.
>>
1
PROG
2 3
5
PROG
PROG
2 / 2