Publicidad
DS-KH6320-WTPE2
E N G L I S H
Video Intercom Two-Wire Indoor Station
Diagram References
Appearance
1
1
Display Screen
2
Microphone
3
Debugging Port
4
Alarm Terminal
5
Two-Wire Interface
6
Loudspeaker
7
Power Supply Interface
Note: The debugging port is used for debugging only.
2
Wiring
AIN1: Alarm Input 1
AIN7: Alarm Input 7
AIN2: Alarm Input 2
AIN8: Alarm Input 8
AIN3: Alarm Input 3
GND: Grounding
AIN4: Alarm Input 4
485-: RS-485 Interface
AIN5: Alarm Input 5
485+: RS-485 Interface
AIN6: Alarm Input 6
Note: Wiring description refers to the User Manual.
Installation
3
The wall mounting plate and the junction box are required to install the indoor station onto
the wall.
The dimension of junction box should be 75 mm (width) × 75 mm (length) × 50 mm (depth).
The dimension of wall mounting plate is shown.
Before you begin:
1. Make sure the device in the package is in good condition and all the assembly parts
are included.
2. The power supply the indoor station supports is 12 VDC. Please make sure your
power supply matches your indoor station.
3. Make sure all the related equipment is power-off during the installation.
4. Check the product specification for the installation environment.
5. Here takes wall mounitng with junction box for example.
Wall Mounting with Junction Box
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the junction box to the hole chiseled on the wall.
3. Fix the wall mounting plate to the junction box with 2 screws.
4. Hook the indoor station to the wall mounting plate tightly by inserting the plate hooks
into the slots on the rear panel of the indoor station, during which the lock catch will be
locked automatically.
Wall Mounting without Junction Box
1. Insert 2 expension tubes into the wall.
2. Fix the wall mounting plate to the wall with 2 screws.
3. Hook the indoor station to the wall mounting plate tightly by inserting the plate
hooks into the slots on the rear panel of the indoor station, during which the lock
catch will be locked automatically.
Getting Started
4
Activate Indoor Station
1
You are required to activate the device first by setting a strong password for it before
you can use the device.
1. Power on the device. It will enter the activation page automatically.
2. Create a password and confirm it.
3. Tap OK to activate the indoor station.
Note: We highly recommend you to create a strong password of your own choosing
(using a minimum of 8 characters, including at least three kinds of following categories:
upper case letters, lower case letters, numbers, and special characters) in order to
increase the security of your product. And we recommend you reset your password
regularly, especially in the high security system, resetting the password monthly or
weekly can better protect your product.
Quick Configuration
2
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automatically.
3. Configure the indoor station and tap Next.
a. Select Indoor Station Type.
b. Edit Floor and Room No.
4. Linked related devices and tap Next. If the device and the indoor station are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the door station in the list to link.
b. Tap the settings icon to pop up the Network Settings page.
c. Edit the network parameters of the door station manually or enable DHCP to get
the network parameters automatically.
d. Optional: Enable Synchronize Language to synchronize the Language of door
station with indoor station.
e. Tap OK to save the settings.
5. Tap Finish to save the settings.
The power supply must conform to LPS. The recommended adaptor models and
manufacturers are shown as below. Use the attached adaptor ,and do not change the
adaptor randomly.
Model
Current
Manufacturer
MSA-C1500CS24.0-40W-DE
1.5A
MOSO POWER SUPPLY TECHNOLOGY CO.,LTD
ADS-40FSI-19 24036EPG
1.5A
SHENZHEN HONOR ELECTRONIC CO.,LTD
Refer to Video Intercom Indoor Station Configuration Guide (scan the QR code) for details.
Refer to Video Intercom Indoor Station Operation Guide (scan the QR code) for details.
Scan the QR code to get the configuration
Scan the QR code to get the operation
guide for detailed information.
guide for detailed information.
1
3
122
Safety Instruction
Warnings
● All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations
and other related regulations in your local region.
● Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the
required value.
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
● Please make sure that the power has been disconnected before you wire, install or dismantle the device.
● When the product is installed on wall or ceiling, the device shall be firmly fixed.
● If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please
contact the service center.
● If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to
Standard
disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or
maintenance.)
CE
CE
Cautions
● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the
equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
● Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature),
cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
● The device cover for indoor use shall be kept from rain and moisture.
● Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden
(ignorance can cause fire danger).
● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a
malfunction however), and affecting the endurance of sensor at the same time.
● Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the
acidic sweat of the fingers may erode the surface coating of the device cover.
● Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline
detergents.
● Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device
to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device
and lead to additional costs.
● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
3 4 5
1
2
Note: Do not wire the cables through the cable
7
hole (red area) when installing the device with
gang box.
Lock Catch
Lock Catch
Unit:mm
Lock Catch
Lock Catch
Rear Panel (without Interface)
Consignes de sécurité
Avertissements :
● Tous les éléments électroniques doivent respecter à la lettre la réglementation locale sur la sécurité des
installations électriques, sur la prévention des incendies et des réglementations connexes en vigueur.
● Utilisez un adaptateur fourni par une entreprise agréée. La consommation électrique ne doit pas être inférieure à la
valeur exigée.
● Ne branchez pas plusieurs appareils sur un même adaptateur ; toute surcharge de l'adaptateur pouvant entraîner
sa surchauffe ou provoquer un incendie.
● Veillez à bien déconnecter la source d'alimentation avant de câbler, installer ou démonter l'appareil.
● Lors de l'installation au mur ou au plafond, assurez-vous que l'appareil est bien fixé.
● Si l'appareil dégage de la fumée ou une odeur suspecte, ou s'il émet des bruits inhabituels, éteignez-le et
débranchez le câble d'alimentation, puis contactez le SAV.
● Si le produit ne fonctionne pas correctement, contactez votre revendeur ou le SAV le plus proche. Vous ne devez en
aucun cas essayer de démonter le produit vous-même. (Nous déclinons toute responsabilité en cas de problèmes
découlant d'une intervention ou d'une réparation effectuée sans autorisation.)
Précautions
● Évitez de faire tomber l'appareil, de le heurter et de l'exposer à des rayonnements électromagnétiques de forte
intensité. Évitez d'installer l'équipement sur des surfaces vibrantes ou à des emplacements subissant des chocs
fréquents (au risque de l'endommager).
● N'installez pas l'appareil à un emplacement trop chaud ou trop froid (reportez-vous à la spécification de l'appareil
pour connaître la température de fonctionnement précise), poussiéreux ou humide. Ne l'exposez pas non plus à des
rayonnements électromagnétiques élevés.
● Le capot de l'appareil pour installation intérieure ne doit pas être exposé à la pluie, ni à l'humidité.
● Il est formellement interdit d'exposer l'équipement directement au soleil, à un environnement mal ventilé ou à une
source de chaleur telle qu'une chaudière ou un radiateur (au risque de provoquer un incendie).
● N'orientez pas l'appareil vers le soleil ou des sources de lumière très vive. Dans le cas contraire, un voile ou des
traînées risquent de se former (ce qui ne constitue toutefois pas un dysfonctionnement) et la résistance du capteur peut
également être affectée.
● Utilisez le gant fourni pour ouvrir le capot du dôme et évitez tout contact direct avec celui-ci, l'acidité de la sudation
des doigts pouvant éroder le revêtement du capot de l'appareil.
● Utilisez un chiffon doux et sec pour nettoyer les surfaces intérieures et extérieures du capot de l'appareil. N'utilisez
pas de détergents alcalins.
● Conservez tous les emballages ; ils pourront vous resservir ultérieurement. En cas de panne, renvoyez l'appareil à
l'usine dans son emballage d'origine. Si l'appareil est transporté hors de son emballage d'origine, il risque d'être abîmé,
entraînant des frais supplémentaires.
● Une mauvaise utilisation de la batterie ou un remplacement erroné peut entraîner un risque d'explosion. Ne la
remplacez que par une batterie identique ou de type équivalent. Mettez les batteries usagées au rebut conformément
aux instructions du fabricant.
2
ALARM IN
6
Hook
Hook
Hook
Hook
Screw
Wall Mounting Plate
Junction Box
Product Information
©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instructions on how to use the Product. The software embodied in the Product is governed by the
user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology
Co., Ltd. ("Hikvision") reserves all rights to this manual. This manual cannot be reproduced, changed, translated,
or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or the
subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual
are the properties of their respective owners. No right of license is given to use such trademarks without express
permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH
THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN
RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR
OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION
BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW.
HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Data Protection
During the use of device, personal data will be collected, stored and processed. To protect data, the
development of Hikvision devices incorporates privacy by design principles. For example, for device with facial
recognition features, biometrics data is stored in your device with encryption method; for fingerprint device,
only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable
data protection laws and regulations, including without limitation, conducting security controls to safeguard
personal data, such as, implementing reasonable administrative and physical security controls, conduct periodic
reviews and assessments of the effectiveness of your security controls.
RS485
Wall
Publicidad
