Crown CT60001HX Manual Original página 21

(see fig. 1). Notice that a special nozzle must be put
on evenly so that it will not fall off during operation�
Quick removal of the special nozzles (see fig. 2)
• Turn protective casing 2 to remove the special noz-
zle 14, 15 or 16 quickly, without touching them and
without waiting for them to cool (see fig. 2.2).Attention:
the special nozzles 14, 15 or 16 can be very hot and
can cause burns, fires or damage to property.
• Return the protective casing 2 to its original position,
before installing another special nozzle 14, 15 or 16.
Charging procedure of the power tool
battery
Initial operating of the power tool
The power tool is supplied with a partially charged
battery 7. Before the first use, the battery 7 must
be fully charged.
Charging process (see fig. 3)
• Press the battery lock 8 and remove the battery 7
(see fig. 3.1).
• Connect the charger 13 to the power supply�
• Insert battery 7 into charger 13 (see fig. 3.2).
• Disconnect the charger 13 from power supply after
charging�
• Remove the battery 7 from the charger 13 and
mount battery 7 in the power tool (see fig. 3.3).
Charger indicators (see fig. 4)
Charger indicators 17 and 18 inform of the battery 7
charging process� Signals of the indicators 17 and 18
are shown on the label 19 (see fig. 4).
• Fig� 4�1 - (the green indicator 17 is on, the battery 7
is not inserted in the charger 13) - the charger 13 is
connected to the power network (ready for charging)�
• Fig� 4�2 - (the green indicator 17 is blinking, the bat-
tery 7 is inserted in the charger 13) - the battery 7 is
being charged�
• Fig� 4�3 - (the green indicator 17 is on, the battery 7 is
inserted in the charger 13) - the battery 7 is fully charged�
• Fig� 4�4 - (the red indicator 18 is on, the battery 7 is
inserted in the charger 13) - the charging process of
the battery 7 is terminated due to inappropriate tem-
perature� When the temperature conditions are nor-
mal, the process of charging will resume�
• Fig� 4�5 - (the red indicator 18 is blinking, the battery 7
is inserted in the charger 13) - the charging process of
the battery 7 is terminated because of its failure� Re-
place the faulty battery 7, its further use is prohibited�
In the process of charging the battery 7
and the charger 13 become hot, it is a
normal process.
Switching the power tool on / off
Switching on:
In order to switch on the power tool, push lock-off but-
ton 5 (to right or to left) and while holding it in position,
push on / off switch 6�
Switching off:
In order to switch off the power tool, release on / off
switch 6�
Design features of the power tool
Temperature protection (see fig. 5)
The temperature protection system enables to auto-
matically deactivate the power tool in case of excess
load or when the temperature of the battery 7 is ex-
ceeding 80°C� The system guarantees protection of
the power tool from damage in case of noncompliance
with the operation conditions�
When this protection system is activated indicators 10
will blink as shown onto fig. 5 during 3 seconds.
Overheating protection (see fig. 5)
Overheating protection system of the engine automati-
cally switches off the power tool in case of overheat-
ing� In this situation, let the tool cool before turning the
power tool on again�
When this protection system is activated indicators 10
will blink as shown onto fig. 5 during 3 seconds.
Overload protection (see fig. 5)
Overload protection system of the engine automati-
cally switches off the power tool when it is operated
in a manner that causes it to draw an abnormally high
current�
When this protection system is activated indicators 10
will blink as shown onto fig. 5 during 3 seconds.
Overdischarge protection
The battery 7 is protected by the safety system against
deep discharge� In case of complete discharge, the
power tool is automatically switched off� Attention: do
not try to switch on the power tool when the protec-
tion system is activated the battery 7 can be dam-
aged.
Indicators of the state of battery charge (see fig. 6)
With the push of the button 9 the indicators 10 show
the state of charge of the battery 7 (see fig. 6).
LED lamp
When the on / off switch 6 is pushed, the LED lamp 4
is automatically switched on that allows to carry out
works in low light conditions�
Quick removal of the special nozzles
Special design of the protective casing 2 allows to
remove the special nozzle 14, 15 or 16 quickly, without
touching them and without waiting for them to cool�
Foldable clip (see fig. 7)
The foldable clip allows you to hang the power tool,
which can be convenient, for example, when climbing
stairs, etc�
English
21