TEFAL PRO MINUTE AUTOCLEAN Manual Del Usuario página 48

1800129688 GV8800 E0 A11_110x154 25/04/13 11:29 Page44
The generator does not
come on and the thermostat
light and the on/off switch
are not illuminated.
Water runs out of the holes
in the soleplate.
Water streaks appear on the
linen.
White streaks come through
the holes in the soleplate.
Brown streaks come through
the holes in the soleplate and
stain the linen.
The soleplate is dirty or brown
and may stain the linen.
There is no steam or there is
little steam.
You have filled the tank but
there is no steam.
The red "removable water tank
empty" is blinking.
Steam escapes from the anti-
scale collector plug
Steam or water escapes under
the appliance.
The "anti calc" indicator is lit.
The soleplate is scratched or
damaged.
If you have any problems or queries please call our Customer Relations team first for expert help and advice:
0845 602 1454 - UK (01) 677 4003 - Ireland or consult our website - www.tefal.co.uk
The appliance is not switched on.
Water has condensed in the pipes
because you are using steam for the
first time or you have not used it for
some time.
The soleplate is not hot enough.
Your ironing board is saturated with water
because it is not suitable for use with a
steam generator.
Your boiler has a build-up of scale because
it has not been rinsed out regularly.
You are using chemical descaling agents
or additives in the water for ironing.
Fabric fibres have accumulated in the
holes of the soleplate and are burning.
You are ironing at too high a temperature.
Your linen is not rinsed sufficiently or you
have ironed a new garment before
washing it.
You are using starch.
The removable water tank is empty (red
blinks).
The steam output control dial is set at
minimum.
The tank is not properly in place.
The removable water tank is empty.
The anti-scale collector plug has not been
tightened correctly.
The anti-scale collector plug is damaged.
The generator is faulty.
You have not pressed the "OK / RESTART"
button.
You have placed your iron flat on a
metallic rest-plate.
You have cleaned your soleplate with an
abrasive or metal pad.
Check that your appliance is correctly plugged in
and press the illuminated on/off switch.
Press the steam control button away from your ironing
board until the iron produces steam.
Decrease the steam output while ironing at low
temperature (steam output control dial on the control
panel). Wait for the thermostat light to go out before
activating the steam control button.
Check that your ironing board is suitable (see page 5).
Rinse the anti-scale collector (see the "descaling your
generator" section).
Never add this type of product in the water tank or in the
boiler (see page 5 for what water may be used).
Clean the soleplate with a non-metallic sponge.
See our recommendations regarding temperature control
setting.
Ensure linen is rinsed thoroughly to remove any soap
deposits or chemicals on new garments which may be sucked
up by the iron.
Always spray starch on the reverse side of the fabric to be
ironed.
Fill the removable water tank. Check that the water tank is
pushed firmly into place until there is a "click".
Increase the steam output (control dial on the control
panel).
Check that the water tank is pushed firmly intoplace until
there is a "click". Press the OK / RESTART button on the
control panel until the indicator goes out.
Fill the removable water tank. Press the OK / RESTART button
on the control panel until the indicator goes out.
Tighten the anti-calc collector plug correctly.
Contact an Approved Service Centre to order a new anti-scale
collector.
Stop using the generator and contact an Approved Service
Centre.
Press the OK / RESTART button on the control panel until the
indicator goes out.
Always place your iron on its base or on the iron rest plate.
Refer to the section « clean the soleplate ».