Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Silverline 128891 Manual De Instrucciones

Ocultar thumbs Ver también para 128891:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 22
GB
l) ALWAYS disconnect from the power supply when leaving the machine unattended
m) When not in use, disconnect from the power source and place the front base on a wooden
block so that the blades are not in contact with anything
n) Replace all blades at the same time. Otherwise, the resulting imbalance will cause vibration
and shorten the service life of the planer and blades
Cutting Tool Safety
WARNING: Before connecting a tool to a power source (mains switch power point receptacle, outlet,
etc.) be sure that the voltage supply is the same as that specified on the nameplate of the tool. A
power source with a voltage greater than that specified for the tool can result in serious injury to
the user, and damage to the tool. If in doubt, do not plug in the tool. Using a power source with a
voltage less than the nameplate rating is harmful to the motor.
Use the correct cutting tool
• Ensure the cutting tool is suitable for the job. Do not assume a tool is suitable without checking
the product literature before use
Protect your eyes
• Always wear appropriate eye protection when using cutting tools
• Spectacles are not designed to offer any protection when using this product; normal lenses are
not impact resistant and could shatter
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 85dB
Protect your breathing
• Ensure that you and others around you wear suitable dust masks
Protect your hands
• Do not allow hands to get close to the cutting wheel or blades. Use a suitable push stick for
shorter workpieces with appropriate power tools
Be aware of others around you
• It is the responsibility of the use to ensure that other people in the vicinity of the work
area are not exposed to dangerous noise or dust and are also provided with suitable
protective equipment
Hidden objects
• Inspect the workpiece and remove all nails and other embedded objects before cutting
• Do not attempt to cut material that contains embedded objects unless you know that the
cutting tool fitted to your machine is suitable for the job
• Walls may conceal wiring and piping, car body panels may conceal fuel lines, and long grass
may conceal stones and glass. Always check the work area thoroughly before proceeding
Beware of projected waste
• In some situations, waste material may be projected at speed from the cutting tool. It is the user's
responsibility to ensure that other people in the work area are protected from the possibility of
projected waste
Fitting cutting tools
• Ensure cutting tools are correctly and securely fitted and check that wrenches/adjusters are
removed prior to use
• Only use cutting tools recommended for your tool
• Do not attempt to modify cutting tools
• Ensure blades are sharp, in good condition and correctly fitted
• Do not attempt to re-sharpen blades that are not suitable for re-sharpening. These may include
specially hardened blades or blades made from hardened alloys typically containing tungsten
• Blades that can be re-sharpened should be re-sharpened only according to the blade
manufacturer's instructions. These may include a limited number of times the blade can be
re-sharpened
• Sharpened blades should be more thoroughly inspected before use and replaced immediately if
there is any doubt about their condition and suitability for use
• In the event blades encounter an embedded object in use that the blades are not suitable for,
blades should be replaced immediately
Direction of feed
• Always feed work into the blade or cutter against the direction of movement of the blade or cutter
6
Beware of heat
• Cutting tools and workpieces may become hot in use. Do not attempt to change tools until they
have been allowed to cool completely
Control dust/swarf
• Do not allow dust or swarf to build up. Sawdust is a fire hazard, and some metal swarf
is explosive
• Be especially careful when cutting wood and metal. Sparks from metal cutting are a common
cause of wood dust fires
• Where possible, use a dust extraction system to ensure a safer working environment

Product Familiarisation

1
Depth Adjustment Handle
2
Dust Extraction Port
3
Safety Lock Off Button
4
Rear Handle
5
Trigger Switch
6
Drive Belt Cover
7
Chamfer Groove
8
Sole Plate
9
Dust Bag
10 Spare Drive Belt
11 Guide Fence Attachment Point
12 Guide Fence
Accessories:
• Spanner
• Spare Brushes (x2)

Intended Use

Hand-held electric planer for light to medium duty planing of hard and softwood timber.

Unpacking Your Tool

• Carefully unpack and inspect your tool. Familiarise yourself with all its features and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool

Before Use

WARNING: Ensure the tool is disconnected from the power supply before attaching or changing
any accessories, or making any adjustments.
Fitting the dust bag
• Slide the Dust Bag (9) into the Dust Extraction Port (2) before using the planer so that dust and
waste are collected safely
• Do not use the planer without the dust bag (or a vacuum system) fitted
• For optimum performance and through-flow of air, empty the dust bag regularly and do not
allow it to become more than half full

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

951152

Tabla de contenido