Dorel Maxi-Cosi Rodi SPS Modo De Empleo página 4

EN
Using the Rodi SPS in the car
The Rodi SPS consists of two parts: a booster seat and a detachable backrest. Always use the booster seat with
the backrest.
We recommend that your child should only use the Rodi SPS when he/she weighs at least 15 kg and is tall enough
for the belt to fit correctly over the shoulder (and not press against the neck). The belt routing areas are marked in
red. You will see a red mark under the armrests of the booster seat and red belt hooks on the headrest. Fitting the
backrest is very simple and is explained in the following section.
IMPORTANT: When using the Rodi SPS in the front passenger seat the car seat must ALWAYS be placed in its most
UPRIGHT POSITION. Remove the headrest of the passenger seat if it is in the way when the Rodi SPS is placed in
the car. Do not forget to replace the headrest when the passenger seat is in use again.
Fitting the backrest
• Fold the U-shaped flaps on the rear of the booster seat double and tuck them under the cover, ensuring that the
openings in the cover are kept unrestricted.
• Insert the hooks of the backrest in the openings (1). Make sure that the backrest is lying flat (horizontal) on the
ground. Make sure that the cover does not get caught between the moving parts of the seat.
• Raise the backrest until you feel some resistance and hear a slight click engaging the backrest (Fig. B-2). Raise the
backrest further until the side lumbar supports come into contact with the armrests.
Removing the backrest
• Push the backrest downwards until you feel some resistance. Gently push the backrest further until it lies flat.
Remove the backrest by carefully lifting the hooks out of the openings in the booster seat.
Adjusting the height of the headrest
• Hold the headrest with one hand at the top. Use the other hand to operate the adjuster.
• Pull the headrest up until you feel some resistance (1).
• Tilt the adjuster on the rear of the backrest slightly upward (2).
• When the required height is reached, release the adjuster and click in the selected position. There are 6 positions.
• Push the headrest carefully down until it stops, so that it locks.
To ensure the correct headrest height is obtained, the red belt hooks should be located slightly above the
shoulders of your child. Make sure that the shoulder belt is positioned correctly over the shoulder of the child (B3)
and does not press against the child's neck. (When the car seat belt height is adjustable, adjust the height so that
the belt runs in a straight line through the belt hooks of the Rodi SPS headrest).
Installing the Rodi SPS
Position the Rodi SPS with its backrest firmly against the backrest of the car seat (fig. C). Make sure that the seat is
not placed on the belt buckle. Sit your child on the Rodi SPS (fig. D) with his/her back against the backrest.
Put the seat belt around the child. Thread the lap belt under both armrests (fig. D-1). If fitted correctly, the belt passes
over the red marking on the seat. Insert the buckle tongue in the belt buckle (fig. D-2) and pull the lap belt tight.
Thread the shoulder belt under the armrest and then through the red belt hook on the headrest (fig. D-3). Make
sure that the belt is not twisted and is positioned correctly over your child's shoulder. Pull the shoulder belt tight.
6
When getting out of the seat, simply release the belt buckle and put the belt to one side. The shoulder belt then
remains positioned in the red belt hook. It is then easy to fit the belt again from this position. Make sure the seat
belt is also fastened when the Rodi SPS is not in use.
Maintenance
• The seat may be cleaned with warm water and a gentle soap. Do not use abrasive detergents.
• The cover must be washed by hand at a maximum temperature of 30o C. Do not use a tumble dryer
(see also washing instructions).
• It is advisable to buy an extra cover when purchasing the Rodi, enabling the seat to be used at all times
(also when the cover is being washed).
Removing the cover
• Take the Rodi SPS out of the car.
• Remove the backrest and headrest as instructed in 'Removing the headrest'.
Booster seat
• Unhook the cover from the pins underneath the booster seat (fig. E).
• Pull the cover over the armrests towards you (fig. F). The cover is now completely loose.
Backrest
• Unhook the cover from the pins on the rear of the backrest (fig. G).
• Pull the cover over the lumbar supports (fig. H). The cover is now completely loose.
Headrest
• Unhook the cover from the pins on the rear of the headrest (fig. I).
• Pull the cover over the headrest (fig. J). Make sure that the foam parts remain in position.
• Loosen the elastic strap over the headrest. The cover is now loose.
The cover can be refitted using the above instructions in the reverse order. Make sure that the cover is properly
secured on the pins and that the belt hooks on the headrest are not obstructed to allow the shoulder belt to pass
through freely.
Note
• The tighter the belts fit on the child, the better your child is protected.
• Ensure the belts are never twisted.
• The seat belt should lie flat and tight over the body.
• The shoulder belt should not press into the neck, but should go over the shoulder (fig. D-3).
• The lap belt should not press into the stomach, but should go over the upper leg.
• Should you have difficulty closing the car seat belt or pulling it tight, please contact your supplier immediately.
In any case do not use the product.
EN
7