Legacy L8653 Instructivo Del Propietario

Owner's Instructions
Part No. : L8653
Portable Air Hose Reel
3/8 in. x 100 ft. Air Hose and Hose Layering Guide
CAUTION: Read all instructions and warnings before operating this product.
SAVE THESE INSTRUCTIONS!
READ AND UNDERSTAND ALL INSTRUCTIONS!
CAUTION: Inspect hose before each use. Do not exceed
300 psi working pressure. Do not kink, twist, knot or
abrade hose. Do not wrap hose around body. Keep hose
away from hot surfaces and/or chemicals.
Keep children away from work areas.
CARTON CONTENTS:
• Reel assembly
• Curved carry handle and grip
• Two support legs
• 3/8 in. x 5 ft. lead-in hose
• Swivel (to connect lead-in hose)
• Folding handle assembly
• Bolts (four short bolts for support legs, two long bolts
for carry handle, six lock nuts, six flat washers
ASSEMBLY:
1. HOSE CONNECTIONS: Use
thread-sealing tape (not
included) to prevent air leaks.
• Attach swivel to female fitting
on side of hose reel opposite
handle lever.
• Attach lead-in hose to swivel.
2. WINDING HANDLE: Attach winding handle to the
handle lever to axle at side of hose reel and tighten securely.
3. BENCH, WALL, OR TRUCK MOUNTING: For mounting
to wall or bench surface, mount reel using the four outer
holes in the mounting base. Mounting fasteners not
included. Reel can be mounted to truck with or without
support legs.
4. MOBILE USE: Fasten the support legs so the shorter
end of each leg is toward the back of reel.
• Use four short bolts (included). Insert bolts first through the
recesses on bottom of support legs, then through outer pair
of holes in reel mounting base. Secure with lock nuts.
• Use two long bolts (included). Insert bolts through handle
bolt holes and then through center holes in mounting
base. Secure with lock nuts under reel base plate.
• Fit grip to free end of carry handle.
5. USING GROUND STAKES: (Stand-alone position)
• Four large holes (capped) are provided at the ends of the
support legs for use with ground stakes (not included) to
reduce movement when placing reel on ground.
Legacy Manufacturing Company
Marion, IA, U.S.A.
OPERATION:
HOSE LAYERING GUIDE: Using the hose layering guide will help reduce hose
tangles by distributing the hose evenly during hose rewinding. Place one hand on
the hose layering guide and slide it back and forth while retracting the hose. The
hose layering guide may be
removed if desired by removing the
hose stopper and retracting hose
through the layering guide. Replace
the hose stopper on the hose.
FOR WALL OR OVERHEAD INSTALLATION :
1. Change the layering guide bracket position by removing the two bolts where
the layering guide bracket bolts to the side of the mounting base.
2. Reattach the layering guide bracket using the same bracket end hole and the
third hole in the side of the mounting base. Tighten bolts securely. Locking Drum
To prevent hose from unwinding when transporting the reel:
1. Make sure hose is completely retracted onto drum.
2. Loosen locking knob located on the right side of reel.
3. Slide knob assembly over flats on axle.
4. Tighten locking knob
WARRANTY
LEGACY MANUFACTURING COMPANY ("LEGACY") warrants that this equip-
ment will be free from defects in material and workmanship for a period of two
years ( except ninety days for hose and normal wear items such as seals, etc. )
from date of purchase, under normal use. LEGACY'S sole obligation under this
warranty is limited to replacing or repairing, free of charge, any equipment that
proves to be defective under normal conditions and use according to the recom-
mendations of LEGACY. To obtain repair or replacement, the equipment must
be shipped to a LEGACY authorized Warranty and Service Center during the
warranty period, transportation charges prepaid, with proof of date of purchase.
In the event of repair or replacement, the warranty period shall not be extended
beyond the original warranty period.
Ph: 319.373.7305
Fx: 319.373.7309
Repair Part Description
RP004068 Swivel for portable air hose reel
service@legacymfg.com
legacymfg.com
INS8653
(Published 2016-12-19)