Triton Multi-Stand MSA 200 Instrucciones De Uso página 3

ASSEMBLY
Fold the legs of the Main Body Assembly (A) fully
outwards. Loosen the round knob and extend
the stem upwards, then tighten.
Note: The legs should pivot firmly. Adjust the
nuts on the leg pivot bolts if necessary.
Fit the Saddles (B) to the stem using the locating
pins on the saddles as shown.
Attach the Front (C) and Rear (D) Quadrants
using the shorter Hex Bolt (E), Small Washers (F)
and Nyloc Nut (G). Do not over-tighten.
Fit the Quadrant Washer (I) onto the longer Hex
Bolt (J) with the hex head located in the tabs on
the washer. Insert the bolt through the slots in
the quadrants, ensuring that it passes through
the washer held within each quadrant and the
hole in the lower stem saddles. Fasten the Large
Washer (H) onto the bolt with the Round Knob
and M6 Nut (K).
Rotate the quadrants until the flat tops are
horizontal then gently nip up the round knob.
Fasten the Head Assembly (L) to the quadrants
using the Pan Head Bolts (M). The round knob
on the clamp which is built into the head should
be on the same side as the round knob on the
quadrant.
Adjust the nut tension on the Hex Bolt (E) if
necessary. The head should pivot firmly, and
should lock tightly at any selected angle when
the quadrant knob is tightened.
WARRANTY
To register your guarantee visit our web site at
www.tritontools.com* and enter your details.
Your details will be included on our mailing list
(unless indicated otherwise) for information on
future releases. Details provided will not
be made available to any third party.
PURCHASE RECORD
GB
Date of Purchase: ___ / ___ / ____
Model: MSA200
Retain your receipt as proof of purchase
Assembly / Warranty
4
WARNINGS
• Make sure the legs are fully opened, and
that both the stem clamp and the quadrant
clamp are fully tightened before applying
heavy loads.
• Do not overload. Max. load per Multi-Stand
100kg (220lb).
• Do not stand on this product.
• When using the head clamp to clamp
materials less than 30mm, use a packing
piece.
• Clamp an extension piece (ie. an offcut of
sheet material - as shown on product
carton) into the head channel if using Multi-
Stand to support material at a height greater
than its maximum adjustment.
• When clamping easily damaged materials,
eg. doors, use thin packing on both sides to
avoid damage.
• Make sure the Multi-Stand is securely
pegged down to the ground when applying
non-vertical loads; or when on steeply
sloping ground.
Triton Precision Power Tools guarantees
to the purchaser of this product that if
any part proves to be defective due to
faulty materials or workmanship within
12 MONTHS from the date of original
purchase, Triton will repair, or at its
discretion replace, the faulty part free of
charge.
This guarantee does not apply to
commercial use nor does it extend to
normal wear and tear or damage as a
result of accident, abuse or misuse.
* Register online within 30 days.
Terms & conditions apply.
This does not affect your statutory rights
Hartelijk dank voor de aanschaf van dit Triton-gereedschap. Deze instructies geven informatie voor een veilige
en doeltreffende bediening van dit product.
Lees deze handleiding zodat u de voordelen van het unieke design van dit product ten volle kunt benutten. Houd
deze handleiding bij de hand en zorg ervoor dat alle gebruikers van dit gereedschap de handleiding hebben
gelezen en volledig hebben begrepen.
INHOUD
Symbolen 5
Onderdelen 5
Montage 6
Garantie 6
SYMBOLEN
Draag altijd gehoorbescherming, een
veiligheidsbril en een stofmasker
ONDERDELEN
A. Voorgemonteerde voetsteun (1)
B. Beugels (4)
C. Voorkwadrant (1)
D. Actherkwadrant (1)
E. Zeskantbout (M6 x 60 mm) (1)
F. Kleine borgring (2)
G. Borgmoer nylon ring (M6) (1)
H. Grote borgring (1)
I. Kwadrantborgring (1)
J. Zeskantbout (M6 x 80 mm) (1)
K. M6 moer ronde knop (1)
L. Kopstuk (1)
M. Cilinderkopbout (M6 x 10 mm) (4)
Waarschuwing
Zorg dat u de handleiding volledig hebt
doorgenomen en begrepen voor u dit
product gebruikt
NL
Inhoud / Symbolen / Onderdelen 5