Listening Through A Receiver (Home Theater); Check Points Before Requesting Service - Samsung 4 Serie Manual Del Usuario

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
Press the ▲ or ▼ button to select Anynet + (HDMI-CEC), then press the ENTER button.
2
 Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
4 Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
5 Press the EXIT button to exit.
➢ If your receiver supports audio only, it may not appear in the device list.
When listening through the receiver, there are restrictions for using the audio-related (MTS, Preferred language)
➢
menus.
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power
➢
failure), the TV Speaker may be set to Off when you turn the TV on again.

Check Points before Requesting Service

Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The Connecting to Anynet + device...
message appears on the screen.
The Anynet + device does not play.
The connected device is not
displayed.
The TV program cannot be
recorded.
Solution
Check if the device is an Anynet + device. The Anynet + system supports Anynet + devices
■
only.
■ Connect only one receiver (home theater).
Check if the Anynet + device power cord is properly connected.
■
Check the Anynet + device's Video/Audio/HDMI cable connections.
■
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
■
■ Check whether the TV remote control is in TV mode.
Check whether it is Anynet + exclusive remote control.
■
Anynet + doesn't work in certain situations. (Searching channels, Plug & Play, etc.)
■
■ When connecting or removing the HDMI cable, please make sure to search devices
again or turn your TV off and on again.
Check if the Anynet + Function of Anynet + device is set on.
■
Check if the Anynet + device is properly connected to the TV and check if the Anynet +
■
(HDMI-CEC) is set to On in the Anynet + Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the TOOLS
button to show the Anynet + menu and select a menu you want.
Select View TV in the Anynet + menu.
■
■ Press the SOURCE button on the TV remote control and select a device other than
Anynet + devices.
■ Press CH, CH LIST, PRE-CH to change to the TV mode.
(Note that the channel button operates only when an Anynet + device with a built-in tuner
is not connected.)
You cannot use the remote control when you are configuring Anynet + or switching to a
■
view mode.
Use the remote control when the Anynet + setting or switching to view mode is complete.
■
You cannot use the play function when Plug & Play is in progress.
Check whether or not the device supports Anynet + functions.
■
■ Check whether or not the HDMI cable is properly connected.
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
■
Search Anynet + devices again.
■
You can connect an Anynet + device using the HDMI cable only. Some HDMI cables may
■
not support Anynet + functions.
Check whether the antenna jack on the recording device is properly connected.
English - 55
TV Air 11
View TV
Select Device ►
►
Record
►
Menu on Device
Device Operation ►
Receiver :On ►
Setup ►
Move
Enter
Return