Listening Through A Receiver (Home Theater); Troubleshooting For Anynet - Samsung 5 Serie Manual Del Usuario

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.
1. Press the TOOLS button. Press the ENTER E button to select Anynet+ (HDMI-CEC).
2. Press the ▲ or ▼ button to select Receiver. Press the ◄ or ► button to select On or Off.
If your receiver supports audio only, it may not appear in the device list.
N
The receiver will work when you have properly connected the Optical IN jack of the
N
receiver to the Optical Out jack of the TV.
When the receiver (home theater) is set to On, you can hear sound output from the
N
TV's Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1
channel sound to the Home theater receiver. When the source is a digital component
such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
When using the Media Play feature, sound may not output properly through the receiver.
N
When listening through the receiver, there are restrictions for using the audio-related (MTS, Preferred language) menus.
N
If there is a power interruption to the TV when the
N
Speaker Select may be set to External Speaker when you turn the TV on again. (see page 22)

Troubleshooting for Anynet

Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet+ device...
appears on the screen.
The Anynet + device does not
play.
The connected device is not
displayed.
The TV programme cannot be
recorded.
The TV sound is not output
through the receiver.
Receiver is set to On (by disconnecting the power cord or a power failure), the
+
Solution
• Check if the device is an Anynet
• Connect only one receiver (home theater).
• Check if the Anynet device power cord is properly connected.
+
• Check the Anynet device's Video/Audio/HDMI 1.3 cable connections.
+
• Check whether Anynet (HDMI-CEC) is set to On in the Anynet+ setup menu.
+
• Check whether the TV remote control is in TV mode.
• Check whether it is Anynet
• Anynet+ doesn't work in certain situations. (Searching channels, Plug & Play, etc.)
• When connecting or removing the HDMI 1.3 cable, please make sure to search devices again
or turn your TV off and on again.
• Check if the Anynet Function of Anynet+ device is set on.
+
• Check if the Anynet device is properly connected to the TV and check if the Anynet
+
(HDMI-CEC) is set to On in the Anynet
• Press the TV button on the TV remote control to switch to TV. Then press the TOOLS button
to show the Anynet menu and select a menu you want.
+
• Select View TV in the Anynet
• Press the SOURCE button on the TV remote control and select a device other than Anynet
devices.
• (Note that the channel button operates only when a tuner-embedded Anynet+ device is not
connected.)
• You cannot use the remote control when you are configuring Anynet+ or switching to a view
mode.
• Use the remote control when the Anynet+ setting or switching to view mode is complete.
• You cannot use the play function when
• Check whether or not the device supports
• Check whether or not the HDMI 1.3 cable is properly connected.
• Check whether Anynet (HDMI-CEC) is set to On in the Anynet
+
• Search Anynet devices again.
+
• You can connect an Anynet
not support Anynet functions.
+
• If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power
cord or a power failure, please repeat the device scan.
• Check whether the antenna jack on the recording device is properly connected.
• Connect the optical cable between TV and the receiver.
English - 38
device. The Anynet system supports Anynet
+ +
exclusive remote control.
+
Setup menu.
+
menu.
+
Plug & Play is in progress.
Anynet functions.
+
device using the HDMI 1.3 cable only. Some HDMI cables may
+
View TV
Device List
Record : DVDR
DVDR MENU
DVDR INFO
Receiver ◄ On
Setup
Move Adjust
U L
devices only.
+
+
setup menu.
+
►
Return
R
+