Listening Through A Receiver; Check Points Before Requesting Service - Samsung 5 Serie Guia Del Usuario

Listening through a Receiver

You can listen to sound through a receiver instead of the TV speaker.
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
Press the ▲ or ▼ button to select Anynet + (HDMI-CEC), then press the ENTER

button.
 Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
4 Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
5 Press the EXIT button to exit.
➢
When the receiver is set to On, you can listen to the TV sound through the 2-channel
receiver.
➢
If the receiver is exclusively for a home theater only (supporting audio only), it may
not appear in the device list.
➢
In case of a content with copyright problems, listening through the receiver may not
properly operate.
➢
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or
a power failure), the TV Speaker may be set to Off when you turn the TV on again. (see page 23)

Check Points before Requesting Service

Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet + device... appears on
the screen.
The Anynet + device does not
play.
The connected device is not
displayed.
The TV programme cannot be
recorded.
BN68-01434A-Eng.indb 42
Solution
Check if the device is an Anynet + device. The Anynet + system
■
supports Anynet + devices only.
■ Connect only one receiver.
Check if the Anynet + device power cord is properly connected.
■
Check the Anynet + device's Video/Audio/HDMI 1.3 cable connections.
■
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet +
■
setup menu.
■ Check whether the TV remote control is in TV mode.
Check whether it is Anynet + exclusive remote control.
■
Anynet + doesn't work at a certain condition. (Searching channels)
■
■ When connecting or removing the HDMI 1.3 cable, please make
sure to search devices again or restart your TV.
Check if the Anynet + Function of Anynet + device is set on.
■
Check if the Anynet + device is properly connected to the TV and
■
check if the Anynet + (HDMI-CEC) is set to On in the Anynet + Setup
menu.
■ Press the TV button on the TV remote control to switch to TV. Then
press the TOOLS button to show the Anynet + menu and select a
menu you want.
Select View TV in Anynet + menu.
■
■ Press the SOURCE button on the TV remote control and select a
device other than Anynet + devices.
■ Press any of CH, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet + device is not connected.)
■ You cannot use the remote control when you are configuring
Anynet + or switching to a view mode.
Use the remote control when the Anynet + setting or switching to
■
view mode is complete.
■ You cannot use the play function when Plug & Play is in progress.
Check whether or not the device supports Anynet + functions.
■
■ Check whether or not the HDMI 1.3 cable is properly connected.
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet +
■
setup menu.
Search Anynet + devices again.
■
You can connect an Anynet + device using the HDMI 1.3 cable only.
■
Some HDMI cables may not support Anynet + functions.
■ Check whether the antenna jack on the recording device is properly
connected.
English - 4
TV P 1
View TV
Select Device 
Record

Menu on Device 
Device Operation

Receiver :On 
Setup

Move Enter
Exit
2008-03-10 오후 3:31:22