Listening Through A Receiver (Home Theater); Troubleshooting For Anynet - Samsung 7 Serie Manual De Instrucciones

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.
1 Press the TOOLS button.
Press the ENTER button to select Anynet+ (HDMI-CEC).
Press the ▲ or ▼ button to select Receiver.

Press the ◄ or ► button to select On or Off.
 Press the EXIT button to exit.
➢
If your receiver supports audio only, it may not appear in the device list.
➢
The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of
the TV.
➢
When the receiver (home theater) is set to On, you can hear sound output from the TV's Optical jack. When the TV is
displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is
a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the
Home Theater receiver.
➢
When using the WISELINK Pro feature, sound may not output properly through the receiver.
➢
When listening through the receiver, there are restrictions for using the PIP and audio-related(MTS, Preferred
language) menus.
➢
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power
failure), the Select Speaker may be set to External Speaker when you turn the TV on again. (see page 32)

Troubleshooting for Anynet +

Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet + device... appears on the
screen.
The Anynet + device does not play.
The connected device is not
displayed.
The TV program cannot be
recorded.
The TV sound is not output through
the receiver.
Solution
■ C heck if the device is an Anynet + device. The Anynet + system supports Anynet + devices
only.
■ C onnect only one receiver (home theater).
■ C heck if the Anynet + device power cord is properly connected.
■ C heck the Anynet + device's Video/Audio/HDMI 1.3 cable connections.
■ C heck whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ C heck whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn't work in certain situations. (Searching channels, Operating WISELINK)
■ W hen connecting or removing the HDMI 1.3 cable, please make sure to search devices
again or your TV off and on again.
■ Check if the Anynet+ Function of Anynet+ device is set on.
■ C heck if the Anynet + device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet + Setup menu.
■ P ress the TV button on the TV remote control to switch to TV. Then press the TOOLS
button to show the Anynet + menu and select a menu you want.
■ S elect View TV in the Anynet + menu.
■ P ress the SOURCE button on the TV remote control and select a device other than Anynet +
menu.
■ P ress CH, CH LIST, PRE-CH, and FAV.CH to change the TV mode.
(Note that the channel button operates only when an Anynet + device with a built-in tuner is
not connected.)
■ Y ou cannot use the remote control when you are configuring Anynet + or switching to a view
mode.
■ U se the remote control when the Anynet + setting or switching to view mode is complete.
You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet + functions.
■ C heck whether or not the HDMI 1.3 cable is properly connected.
■ C heck whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ S earch Anynet+ devices again.
■ Y ou can connect an Anynet + device using the HDMI 1.3 cable only. Some HDMI cables may
not support Anynet + functions.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
English - 1
View TV
Device List
Recording : DVDR
DVDR Operation
Receiver ◄ On ►
Setup
Move Adjust Return