Tabla de contenido
Publicidad
Technical specifications
Voltage
230 – 240 V/50 Hz
Output
1650 W
Airflow rate
up to 650 l/min., continuously adjustable
Temperatures
stage 1:
stage 2:
Jumper
red:
orange:
yellow:
grey:
blue:
Protection class
II (without earth terminal)
Tool features
1
Stainless steel outlet nozzle
5
ON/OFF switch/2-stage switch
2
Outlet nozzle with lattice guard
6
Jumper for fixed temperature
keeps out foreign matter
setting (up to 450° – 600°C on
leaving the factory)
3
Retaining screw for
changing the heating element
7
Dial for precision adjustment of
temperature and air flow
4
Industrial grade rubber power
cord
For your safety
The thermal cut-out shuts the tool down if it is overloaded.
CE
Declaration of Conformity
This product complies with Low Voltage Directive 06/95/EC, EMC Directive 04/108/EC and RoHS Directive
02/95/EC.
Tool description - Operation
Operation
The tool is switched ON and OFF at the 2-stage switch on the front of the grip. The distance from the object
you are working on depends on material and intended method of working. Always try out airflow and tem-
perature on a test piece first. Using the attachable accessory nozzles (see accessories page on the cover)
the flow of hot air can be controlled with maximum precision.
A small quantity of smoke may occur the first time the tool is used; this is normal and will soon subside.
5
Switch the tool OFF by sliding the switch
to the "0" setting
Exercise care when changing hot nozzles! When using the hot air gun in the self-resting position, make
sure it is standing on a stable, non-slip and clean surface.
Basic temperature setting, "jumpers"
Stage 1 is the cold-air stage, temperature is always 25°C (room temperature). Use the cold-air function for
drying paint, cooling workpieces or for cooling the nozzle before changing the accessory attachment.
In stage 2, the air delivery temperature is determined by the jumper you are using and by the dial setting.
Other temperature ranges can be set using interchangeable jumpers
cations). Storage is also provided by the jumper holder in the stand. To change the jumper, first disconnect
the tool from the mains power supply. Use your index finger and thumb to remove jumper no longer needed
from the tool. Select the temperature (jumper) you require from the holder in the stand and plug it into the
tool. You may continue using the tool once the jumper has clipped into place.
ca. 25 °C
up to 100 – 600 °C, depending on jumper
up to 450 – 600 °C
up to 350 – 450 °C
up to 250 – 350 °C
up to 150 – 250 °C
up to 100 – 150 °C
8
Ergonomic soft grip handle
9
Set of jumpers (accessory)
for changing temperature
10
Stand with jumper storage
11
Locking button
12
Rest
9
(accessory). (see Technical specifi-
- 8 -
Tool description - Operation
Precision adjustment of temperature, setting the airflow rate
Turning the dial
7
allows you to adjust the temperature within specific ranges and also set the airflow rate.
Turning anticlockwise (LO mark) reduces the temperature and increases the airflow rate. Turning clockwise
(HI mark) increases the temperature and reduces the airflow rate. For temperature range guide values, see
Technical specifications.
Working with the stand
Press the locking button using your thumb and index finger
lease the locking lever. Pressing the locking button allows you to turn the HG 1750 backwards and forwards
to change the direction of air delivery.
Use without the stand
Before using the tool without the stand, the rest must be mounted to the ventilation slots on the
motor
12
. The tool can now be set down safely without the stand.
Changing the heating elements
The plug-in heating element in the HG 1750 can be changed in a matter of seconds.
1. Important ! Disconnect tool from power supply. Be careful if the tool has just been in use.
The guard sleeve will still be very hot. Let it cool down first.
3
2. Undo the screws
at the end of the guard sleeve.
3. Detach guard sleeve.
4. Detach heating element and replace it with a new one.
5. Push guard sleeve back on again and screw into place.
Functional warranty
This STEINEL product has been manufactured with utmost care, tested for proper operation and safety
and then subjected to random sample inspection. STEINEL guarantees that it is in perfect condition and
proper working order. The product is guaranteed for 12 months or 500 hours of operation commencing
on the date of sale to the consumer. We will remedy defects caused by material flaws or manufacturing
faults. The warranty will be met by repair or replacement of the defective parts at our own discretion. This
guarantee does not cover damage to wearing parts, damage or defects caused by improper treatment or
maintenance nor does it cover breakage as a result of the product being dropped. Further consequential
damage to other objects is excluded. Claims under warranty shall only be accepted if the product is sent
fully assembled and well packed complete with receipt or invoice (date of purchase and dealer's stamp)
to the appropriate service centre or handed in to the dealer within the first 6 months. Repair service: Our
Customer Service Department will repair faults not covered by the warranty or occur-
ring after the warranty has expired. Please send the product well packed to the Service
Centre.
Accessories
J
Your retailer keeps a stock of these accessory nozzles
A
Reduction nozzle for de-soldering...
Prod. No. 076955
B
Surface nozzle for drying, blister packaging...
Prod. No. 077259
11
and insert the tool into the guide. Now re-
C
Reflector nozzle, large, for shrinking cable sleeves
Prod. No. 077051
D
Reflector nozzle, small, for shrinking cable sleeves
Prod. No. 077150
- 9 -
Publicidad
Tabla de contenido
