Periodic Maintenance - BTI 220 Manual Del Usuario

9
Refer to the table Technical Data specific for your product,
that you will find in the package, for the maximum drilling
diameter and the maximum motor power.
Instructions for use
Before starting to set you system up, read
carefully the user manual of the core drill motor
and of all the other parts of the system (pump,
anchors...).
Proceed as follows:
if available for your rig, mount the F system by
screwing it on. Make sure it is securely
tightened;
fasten the stand on the surface, as described
in the previous
paragraph;
Warning: always ensure that the fastening
mode is suitable for the application and that the
stand is securely fastened;
if needed, tilt the column as shown in the
paragraph Tilting the column;
mount the feed handle (E) according to the
paragraph Feed handle;
mount the core drill motor according to the
instructions of the Core drill motor mounting
paragraph. See Maximum drilling diameter and
core drill motor limitations for limitations;
refer to the user manual provided by the core
drill motor manufacturer for further instructions
and limitations;
Warning: before proceeding ensure that all
bolts and screw are securely tightened.
mount the core bit to the drill motor;
switch the motor on, applying light pressure
drill about 1 cm deep into the workpiece. This
allows core bit centring preventing core bit
side shifting;
after this, apply sufficient pressure to achieve
smooth progressive drilling.
Maintenance - Service - Warranty

Periodic maintenance

keep your drill stand clean and dry, in particular
its base and rack;
never use solvents or other harsh chemicals for
cleaning your core drill;
after use put your stand in a dry, safe and
inaccessible to children place;
do not use the stand with damaged components
or with malfunctions. In these cases, ask a BTI
authorized service centre for replacement.
Service
any repairing operation must be carried out by
BTI authorized service personnel only. Ask your
dealer for the list of the BTI authorized service
centres;
use original BTI spare parts only.
Drill Stand Fastening
Warranty
Your product is under BTI warranty for 36 months, starting
from the date of purchase. This warranty is against faulty
workmanship, flaws material and design problems. The
warranty covers free components replacement, manpower
needed for replacement and wearing materials if intact
before the repairing operation. The warranty doesn't cover
the replacement of:
components of the product replaced or modified
by people not authorized by BTI;
components damaged by carelessness, not
suitable use or overloaded;
components of products from which safety
devices have been removed;
worn wearing parts replaced.
This warranty does not apply to products that have been
damaged by carelessness like lack of periodic cleaning and
maintenance, damage to the rack etc.
The life of wearing parts is variable depending on the
working time and the kind of work they are used for.
Examples of wearing parts are: ball and roller bearing not in
oil, rubber seal etc.
If during repair under warranty, a wearing part is worn and
this can affect the safety and the operation of your product,
the customer is asked to pay for the replacement of these
components not under warranty. If the customer refuses
this, no repairing operation will be carried out.
The warranty covers free replacement of components which
are defective due to wrong manufacturing or assembly, if
the product is brought to an authorized service centre and
if:
the product is together with a purchasing
document stating when the product has been
purchased. Valid purchasing documents are
invoices or delivery certificates;
cleaning and maintenance has been carried out
regularly;
no unauthorized people have serviced the
product;
the product has not been misused and it has
been used accordingly with the directions given
in this user manual;
all safety directions have been followed.
Your BTI product is not under warranty if:
the product has been serviced by people not
authorized by BTI.
damage is due
carelessness. Dents due to drops or strokes will
be considered evidence of carelessness;
damage has been caused by overload;
When your product is under warranty, in some cases, like if
the BTI authorized service personnel think the repairing is
too expensive to be carried out, the free substitution of the
product is possible. In addition, the substitution under
warranty is provided after two fruitless reparation attempts
and after the authorization of a BTI service manager. In
case of substitution, the customer is, usually, requested to
pay for the worn wearing parts of the product that has been
replaced.
User-replaceable components
No components of the BTI product can be replaced by the
user. Replacement must be carried out by BTI authorized
personnel only.
English
to incorrect use and/or