Berner BACD BL 12 V Manual Original página 12

OBJ_BUCH-3427-001.book Page 12 Wednesday, October 11, 2017 4:00 PM
 Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing ac-
cessories, or storing power tools. Such preven-
tive safety measures reduce the risk of starting
the power tool accidentally.
 Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in
the hands of untrained users.
 Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many acci-
dents are caused by poorly maintained power
tools.
 Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edg-
es are less likely to bind and are easier to con-
trol.
 Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the pow-
er tool for operations different from those intend-
ed could result in a hazardous situation.
Service
 Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the pow-
er tool is maintained.
Safety Warnings for Drills
and Screwdrivers
 Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
 Hold power tool by insulated gripping surfaces
when performing an operation where the cut-
ting accessory or fastener may contact hidden
wiring. Cutting accessory and fasteners contact-
ing a live wire may make exposed metal parts of
the power tool live and could give the operator
an electric shock.
 Use appropriate detectors to determine if util-
ity lines are hidden in the work area or call the
local utility company for assistance. Contact
12 | English
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage.
 Switch off the power tool immediately when
the tool insert jams. Be prepared for high reac-
tion torque that can cause kickback. The tool
insert jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
 Hold the machine with a firm grip. High reac-
tion torque can briefly occur while driving in and
loosening screws.
 Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
 Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over the
power tool.
 Do not open the battery. Danger of short-circuit-
ing.
Protect the battery against heat, e. g.,
against continuous intense sunlight,
fire, water, and moisture. Danger of ex-
plosion.
 In case of damage and improper use of the
battery, vapours may be emitted. Ventilate the
area and seek medical help in case of com-
plaints. The vapours can irritate the respiratory
system.
 Use the battery only in conjunction with your
Berner product. This measure alone protects
the battery against dangerous overload.
 The battery can be damaged by pointed ob-
jects such as nails or screwdrivers or by force
applied externally. An internal short circuit can
occur and the battery can burn, smoke, explode
or overheat.
Products sold in GB only: Your product is fitted
with a BS 1363/A approved electric plug with inter-
nal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in
its place by an authorised customer service agent.
The replacement plug should have the same fuse
rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be insert-
ed into a mains socket elsewhere.
Products sold in AUS and NZ only: Use a residual
current device (RCD) with a rated residual current
of 30 mA or less.
1 609 92A 44E • 11.10.17