Cleaning And Maintenance - STAMONY ST-HC-8000B Manual De Instrucciones

CONTROL PANEL
F
A B
E
C
D
G
A. Menu: Open the settings menu
B. SHOT: Start recording video manually or take a picture
depending on the mode set. Video recording will end
when this button is pressed.
C. REPLAY: Press this button to enter the playback mode.
D. OK: No function in recording mode
E. Directional buttons (up, down, right, left)
F. : Activates the manual video recording mode.
G. : Activates manual shooting mode.
3.2. PREPARING FOR USE
APPLIANCE LOCATION
It is recommended to place the camera 1-2 meters above
the ground.
The temperature of environment must not be higher
than 40°C and the relative humidity should be less than
85%. Keep the product away from hot surfaces. Position
the device such that you always have access to the power
plug. The power cord connected to the appliance must be
properly grounded and correspond to the technical details
on the product label.
ASSEMBLING THE APPLIANCE
Battery installation
1. Press the latch lightly and open the battery
compartment.
2. Install batteries according to the polarity marking
inside the compartment.
3. Close the battery compartment cover.
Caution: Installing any of the batteries in the wrong
position may cause acid leakage or explosion, which
may damage the device.
EN
Connecting to the power supply
1. Remove the rubber plug from the power cord port
located at the bottom of the device.
2. Connect the adapter cable to the device port.
3. Route the cable through the hook on the side of the
device. This will reduce the forces on the cable and
power port that can damage them.
4. Connect the adapter to the wall socket.
5. When the power port is not in use, reinstall the rubber
plug.
Installing a memory card
1. Insert the memory card until it clicks. The card should
slide in with a slight resistance.
2. To eject the memory card, push the card in lightly.
3.3. DEVICE USE
„TEST" mode
Slide the mode switch from OFF to the TEST position to start
the device and display the settings. It is not recommended to
move the switch directly from OFF to ON. TEST mode, allows
you to change the device settings, manually taking photos
and videos, viewing photos and videos.
10
ADVANCED SETTINGS
1 6 9
2 7 10
3 8 11
12
4
5 13
14
15
16
17
18
No. Parameter Submenu Description
name
1 Resolution 16MP, 12MP, Photo quality
8MP
2 Sequence 1/3/6/9 The number of
photos taken each
time
3 ISO Auto, 100, Sensitivity of the
200, 400 matrix to light
4 Delay 1/5/10/30 Waiting time since
sec/min last shot
5 ID cameras 0-0-0 -
0-0-0
6 Resolution 1080P, 720P, Video quality
WVGA, VGA
7 Video 10S, 30S, 60S, Video duration
lenght 90S
8 Sound On, Off Sound recording
recording on/off
9 Mode photos, video, -
photo and
video, time-
lapse mode
10 Language English, Menu language
Francais,
Deutsch etc.
11 Time-lapse 5/30/60 Making a film
interval or photo every
5/30/60 min
12 TV mode NTSC, PAL TV play mode
13 Date/time 2018-09-03 Time-Month-Day
16:37:25 Hours: minutes:
seconds
EN
14 Timer ON, OFF If it is on, the device
will only work for
limited time
15 Password **** 4-digit number
(1314 universal
password)
16 Format SD card Delete all data from
the memory card
17 Default Restore Cancel / OK
settings default
settings
18 Version 18-09-03 Camera version
16:37
„ON" mode
After completing the settings, slide the switch to the ON
position to switch to automatic operation mode.
The motion indicator will flash for about 5 seconds and the
camera will start working. The device will start recording
video or take pictures when motion is detected in the
sensor's operation zone.
Caution: The device display and control panel buttons
will be inactive when the device is in „ON" mode. To view
content or change device settings, slide the mode switch to
the TEST position.
Caution: To avoid accidental starts due to temperature or
movement, do not point the device at heat sources (e.g.
sun, heated stones or metal) or nearby branches of trees
and bushes. The best direction in which the device should
be directed is north and an open space without heat
sources. It is also recommended to remove branches from
before the device.

3.4. CLEANING AND MAINTENANCE

a) Always unplug the device before cleaning it.
b) Use only non-corrosive cleaners to clean the surface.
c) After cleaning the device, all parts should be dried
completely before using it again.
d) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
e) Do not spray the device with a water jet or submerge
it in water.
f) Use a soft cloth for cleaning.
g) Do not leave the battery in the device if it will not be
used for a longer period of time.
SAFE REMOVAL OF BATTERIES AND RECHARGEABLE
BATTERIES
AA batteries are installed in the devices. Remove used
batteries from the device using the same procedure
by which you installed them. Recycle batteries with the
appropriate organisation or company.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used
to construct the device can be recycled in accordance
with their markings. By choosing to recycle you are
making a significant contribution to the protection of our
environment.
Contact local authorities for information on your local
recycling facility.
11