English - Berner BACRHD BL SDS MAX 18V Manual Original

TECHNICAL DATA
Code ...............................................................................................................
Drilling capacity in concrete ...........................................................................
Tunnel bit in concrete, bricks and limestone..................................................
Core cutter in concrete, bricks and limestone ...............................................
No-load speed ................................................................................................
Rate of percussion under load .......................................................................
Impact energy per stroke according to EPTA-Procedure 05/2009 ........
Chuck neck diameter .....................................................................................
Battery ............................................................................................................
Battery voltage ...............................................................................................
Weight according EPTA-Procedure 01/2003 (3.0/4.0/5.0 /9.0 Ah) ................
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) .............................................................
Sound power level (K = 3 dB(A)) .................................................................
Wear ear protection!
Total vibration values (vector sum in the three axes) determined according
to EN 60745:
Hammer-drilling in concrete: vibration emission value a
Uncertainty K = .............................................................................................
Chiselling: vibration emission value a
Uncertainty K = .............................................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be
used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not
actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in electric shock, fi re
and/or serious injury.
Save all warnings and instructions for future reference.
ROTARY HAMMER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of control can
cause personal injury.
Hold power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a „live" wire may make exposed metal parts
of the power tool „live" and could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with
the machine. The use of protective clothing is recommended, such as
dust mask, protective gloves, sturdy non-slip footwear, helmet and ear
defenders.
The dust produced when using this tool may be harmful to health. Do not
inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force. Determine why the
insertion tool stalled and rectify this, paying heed to the safety
instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down

ENGLISH

457 098 - Berner-BACRHD BL MAX 18V.indd 14 457 098 - Berner-BACRHD BL MAX 18V.indd 14
CORDLESS ROTARY HAMMER
.............................
h
..........................................................
h
BACRHD BL SDS MAX 18V
BACRHD BL SDS MAX 18V 01 00001-99999
.............. 40 mm (SDS-max)
.............. 65 mm (SDS-max)
............ 100 mm (SDS-max)
......... 0-450 min
-1
....... 0-3000 min
-1
............. 6,1 J
.............. 66 mm
......... Li-Ion
.............. 18 V
............. 6,6 kg
........... 93,6 dB (A)
......... 104,6 dB (A)
........... 10,6 m/s 2
............. 1,5 m/s 2
............. 9,6 m/s
2
............. 1,5 m/s
2
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables
and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces
can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. Your power tool distributor will normally retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit
risk).
Use only System Berner chargers for charging System Berner battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse thoroughly
for at least 10 minutes and immediately seek medical attention.
Lithium Ion batteries submit only discharged at the collection points. Pole
isolated to avoid short circuits.
No metal parts must be allowed to enter the battery section of
the charger (short circuit risk).
SPECIFIED CONDITIONS OF USE
The battery rotary pneumatic hammer may be used for hammer drilling
and drilling in wood, metal as well as plastic for independent use away
from mains supply.
Do not use this product in any other way as stated for normal use.
14
18.07.2017 14:07:52 18.07.2017 14:07:52