Starting Up; Steam Cleaning; Topping Up The Boiler Water Tank With Water; After Use - Lavor GV KATLA Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21
11 Do not use the appliance for steam cleaning
electrical appliances or electric sockets.
12 Once the appliance is plugged in, do not work
with wet hands or feet.
13 Do not immerse the appliance in any liquid.
14 Do not steam-clean the appliance.
15 Service and repairs must be carried out by
qualified personnel only. Only use manufacturer
original spare parts for service repair.
16 Before connecting the appliance, make sure
that the nameplate data are the same as those of
the electrical mains and that rhe socket is protect-
ed by a differential security breaker with tripping
sensitivity below 0.03 A - 30 ms.
17 Ensure that power sockets used ore correct for
the machine.
18 Never use the appliance in ambient
temperatures below 0°C if it is equipped with a
PVC (H VV-F) cable.
19 The electric cable must be replaced only by an
authorised service centre.
20 Do not vacuum explosive, toxic and
inflammable substances (e.g. chimney ashes and
soot) or substances that may be dangerous to
your health.
23 Do not place the suction orifice near delicate
parts of the body such as eyes, mouth and ears.
25 Never obstruct the steam outlet.
26 Do not point the steam jet towards people or
animals.
27 During use the appliance could overheat if
covered.
28 If the appliance is lent to someone else, the
instruction manual should also be passed on.
29 The appliance is not to be used by children or
persons with reduced physical, sensory or men-
tal capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or
instruction.
30 Children being supervised not to play with the
appliance.

STARTING UP

When preparing the appliance for use, switch
it off and unplug it!
- Fill the tank J with water (fig. 1)
Do not put any kind of detergent or chemical
substance in the water tank!
- Fill the tank J
with detergent (fig. 2)
1
- Put (◊,+, -,*) hose on (◊,+, -,*) hole on the tank
(fig. 3)
This appliance is designed for use with the
detergent supplied or recommended by the
manufacturer. The use of other detergents or
chemicals may put the appliance's safety at
risk!
- Fit the nozzle H
1
connection H
(fig. 4-5-6)
2

STEAM CLEANING

• Fit the most suitable accessory in the handle
of the flexible hose L.
• Connect the device to a suitable electrical
outlet.
• Start vacuuming by pressing main switch B
• Turn on the steam system using switch E and
wait until "steam ready" light D lights up.
• Selection with switch (P)
_
: INJECTION HOT WATER
: DRY STEAM
o
=
: INJECTION DETERGENT
- To help the primer of the injection pump,
turn the steam tap F off and press the
switch L
3
- Pre-select the amount of steam using
the knob F located on the appliance. The
gauge R indicates the pressure inside the
boiler.
TOPPING UP THE BOILER WATER TANK WITH WA-
TER
• The boiler water tank L supplies the boiler
through an electronic level control; since this
is an external tank, it can be topped up any
time.
• When water runs out in the boiler water
tank:
1. the appliance beeps intermittently
2. the no-water level pilot light C flashes
3. the steam stops coming out
To top up, proceed as follows:
• Switch off the boiler switch E
• Turn off the main switch B
• Remove the cable from the socket
• Fill the boiler water tank J

AFTER USE

• Every time you finish working, put switch B, E
and P in OFF position.
• Extract the plug from the wall socket.
of the flexible hose L in the
EN
11

Publicidad

Tabla de contenido
loading

Productos relacionados para Lavor GV KATLA

Tabla de contenido