EWT Optiflame BIZET BZT20 Manual Del Usuario página 4

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice:
When using electrical appliances, basic precautions should always be
followed to reduce the risk of fire, electrical shock and injury to persons,
including the following:
If the appliance is damaged, check with the supplier before installation and
operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower or swimming
pool.
Do not locate the heater immediately below a fixed socket outlet or
connection box.
This appliance is not intended for use by children or other persons without
assistance or supervision if their physical, sensory or mental capabilities
prevent them from using it safely. Children should be supervised to ensure
that they do not play with the appliance.
Do not use this heater in series with a thermal control, a program controller,
a timer or any other device that switches on the heat automatically, since a
fire risk exists when the heater is accidentally covered or displaced.
Ensure that furniture, curtains or other combustible material are positioned
no closer than 1 metre from the heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we do not recommend
its use on deep pile carpets or on long hair type of rugs.
The appliance must be positioned so that the plug is accessible.
If the supply cord is damaged it must be replaced by the manufacturer or
service agent or a similarly qualified person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
WARNING: In order to avoid overheating, do not cover the heater. Do
not place material or garments on the heater, or obstruct the air
circulation around the heater. The heater carries the Warning symbol
indicating that it must not be covered.
General
Unpack the heater carefully and retain the packaging for possible future use, in the
event of moving or returning the fire to your supplier.
The fire incorporates a flame effect, which can be used with or without heating, so that
the comforting effect may be enjoyed at any time of the year. Using the flame effect on
its own only requires little electricity.
Before connecting the heater check that the supply voltage is the same as that stated
on the heater.
Please note: Used in an environment where background noise is very low, it may
be possible to hear a sound which is related to the operation of the flame effect.
This is normal and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage marked on the
heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating instructions.
Wall fixing
- see Fig. 1
The appliance should be securely fixed to the wall using the wall plug and screw
supplied for block walls.
Note - for studded walls special fasteners are required, see diagram for recommended
position of fixing screws.
Recessed Installation
Please note that this appliance can also be wall-mounted so that it is recessed. This
can be installed in a large fireplace opening or a purpose built wall. See Table 1 for
size of recess required and hole fixing dimensions.
This fireplace insert does NOT require venting.
In order to ensure its future safety in use, it is essential that this fire is securely
fixed to the wall.
IT IS IMPORTANT THAT THE FIXING DEVICE CHOSEN IS APPROPRIATE TO THE
WALL MATERIAL TO WHICH THE FIRE IS BEING FIXED. SOME MODERN
INTERNAL BUILDING MATERIALS ARE VERY LOW DENSITY BLOCK AND
REQUIRE SPECIALIZED FIXING DEVICES TO PROVIDE A SAFE, SECURE
INSTALLATION.
The installation of this fire should be carried out by a competent person. If in doubt
please consult your local builder. This section provides step by step instructions for
selecting a location and preparing the site to install the fireplace into the following:
Existing Fireplace
1. Make sure that the fire is located on a flat surface.
2. Seal all draughts and vents to prevent chimney debris from falling onto the
Fireplace Insert. Do not install into an existing fireplace that is prone to dampness.
3. Remove the front/trim by following the steps as outlined above.
4. Locate the 4 fixing holes, position the fire accordingly, and firmly fix the appliance
to the wall using the appropriate screws.
5. Replace the front/trim.
New Support Structure Construction
When planning where to position your purpose built support structure the following
steps must be observed:
1. Place the fire in the desired location to see how it will look in the room.
2. Mark the desired location for the new support structure in the room and store the
fire in a safe, dry and dust free location.
3. Using timber studs to support the fire, devise and construct a suitable means of
supporting the product within the wall partition and provide electrical power for the
fire to be HARD wired. For recommended sizes of height, width and depth of
opening for recess and hole fixing dimensions for each model:
4. Remove the front/trim by following the steps as outlined above.
5. Locate the 4 fixing holes, position the fire accordingly, and firmly fix using the
appropriate screws.
6. Replace the front/trim.
NOTE: The appliance should be HARD wired to an electrical power outlet when placed
in a recessed installation. Please consult a qualified electrician for appropriate wiring
requirements.
Controls
- see Fig. 2
Three switches provide a choice of heat settings. A switch is in the ON position when
the side with the markings on (i.e. I, I, or II) is pushed in.
Switch 1 (I) Controls the electricity supply to the heater and flame effect.
Note: This switch must be in the ON (I) position for heater to
operate with or without heat.
Switch 2 (I) Provides 1kW heat output
Switch 3 (II) Provides 2kW output with switch 2
Thermostat (T)
- see Fig. 2
In order to maintain a certain room temperature, set the controller to 'max.'. Operate
the appliance at full power until the required room temperature is reached. Set back
the thermostatic controller until the appliance switches off with an audible "click". This
temperature will be kept almost constant by the thermostatic control switching on and
off automatically. Please note that the appliance can only be switched on when the
thermostat setting is higher than the room temperature.
Remote control
- see Fig. 7
The maximum range of use is ~ 15metres.
Warning: It takes time for the receiver to respond to the transmitter.
Do not press the buttons more than once within two seconds for correct operation.
Battery information
- see Fig. 7
1. Slide open the battery cover on the back of the remote control.
2. Install AAA batteries into the remote control.
3. Replace the battery cover.
Discard leaky batteries
Dispose of batteries in the proper manner according to provincial and local regulations.
Any battery may leak electrolyte if mixed with a different battery type, if inserted
incorrectly, if all the batteries are not replaced at the same time, if disposed of in a fire,
or if an attempt is made to charge a battery not intended to be recharged.
Thermal Safety Cut-out
A thermal safety cut-out is incorporated in the heater to prevent damage due to
overheating. This can happen if the heat outlet was restricted in any way. The heater
will switch on once the obstruction has been removed and the heater has cooled. If the
cut-out continues to operate intermittently, the heater should be switched off and a
service agent contacted.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
ATTEMPTING ANY MAINTENANCE.
Lamp Replacement
- See Fig. 3, Fig. 4 and Fig. 5
Remove front cover.
Using a coin edge or screwdriver turn catch 1/4 turn clockwise.
Pull the tray forward, the bulbs can now be replace with a 60W E14 SES Clear Candle
lamp.
Take care not to over-tighten the lamp.
Trim colour options
- see Fig 6
The fire comes with a reversible trim.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive cleaners. The glass
viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary
glass cleaners.
To remove any accumulation of dust or fluff the soft brush attachment of a vacuum
cleaner should occasionally be used to clean the outlet grille of the fan heater.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not be disposed of with
household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
After Sales Service
Should you require after sales service or should you need to purchase any spares,
please contact the retailer from whom the appliance was purchased or contact the
service number relevant to your country on the warranty card. Please do not return a
faulty product to us in the first instance as this may result in loss or damage and delay
in providing you with a satisfactory service. Please retain your receipt as proof of
purchase.
- 1 -
UK