Tabla de contenido
Publicidad
mental limitations or a lack
of experience or knowledge
if a person responsible for
their safety supervises them
or has instructed them in the
safe operation of the charger
and they understand the
associated dangers (otherwise,
there is a danger of operating
errors and injuries)
• Supervise children (this will
ensure that children do not play
with the charger)
• Cleaning and user
maintenance of the battery
charger shall not be made by
children without supervision
•
Do not expose tool/charger to rain
•
Do not charge battery in damp or wet environments
Do not use charger when damaged; take it to one of the
•
officially registered SKIL Service Stations for a safety
check
•
Do not use charger when cord or plug is damaged; cord
or plug should be replaced immediately at one of the
officially registered SKIL Service Stations
•
Do not disassemble charger or tool
•
Permitted ambient temperature (tool/charger/battery):
- when charging
- during operation
- during storage
EXPLANATION OF SYMBOLS ON TOOL/CHARGER
3 Read the instruction manual before use
4 Only use the charger indoors
5 Double insulation (no earth wire required)
6 Do not dispose of electric tools and batteries together
with household waste material
USE
•
Charging battery 2
- connect charger A with both wall socket and contact B
- indicator C starts blinking GREEN indicating that the
battery is being charged
- after 3 hours the battery is fully charged and charging
automatically stops (green light stays on after blinking)
- if the tool is used only briefly, the charging time can be
very short
- unplug the charger when the battery is fully charged
IMPORTANT:
- if indicator C starts blinking RED, this may mean that
the battery is too cold or too hot; when the battery
temperature returns to between 0°C and 45°C, the
charger will automatically begin charging
0...+45°C
–20...+50°C
–20...+50°C
- the lithium-ion battery can be charged at any time
(interrupting the charging procedure does not damage
the battery)
- while charging, tool and charger may become warm to
touch; this is normal and does not indicate a problem
•
Battery protection
Switches off the tool or reduces the speed automatically
when
- the load is too high
- the battery is empty
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
•
On/Off 7
Speed control for smooth starting 8
•
•
Changing direction of rotation 9
- indicator F shows the selected direction of rotation
- when not properly set in left/right position, switch D 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
•
Changing bits q
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
! only use sharp bits
•
Torque control (VariTorque) w
- output torque will increase as clutch ring H is rotated
from 1 to 17; position J will lock up the clutch to permit
drilling or driving heavy duty work
- when turning in a screw, first try VariTorque position 1
and increase until the desired depth has been reached
•
Mechanical gear selection e (2330)
- set selector K to desired speed
! actuate the gear selector while tool is running
slowly
LOW
- low speed
- high torque
- for screwdriving and drilling large diameters
- for tapping thread
HIGH
- high speed
- lower torque
- for drilling small diameters
•
Battery level indicator C r
- indicates the charge condition of the battery for a few
seconds when switch D 2 is pressed half or fully
through
- consists of a two-colour LED
- continuous lighting, green : 33-100%
- continuous lighting, red : 11-33%
- flashing light, red : < 11%
•
Spot light t
Spot light L automatically lights on when activating switch
D 2
•
Holding and guiding the tool
! while working, always hold the tool at the grey-
coloured grip area(s) y
- keep ventilation slots M 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
10
Publicidad
Tabla de contenido
