Chamberlain 940-315CB Manual Del Propietário

OWNER'S MANUAL
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
CAUTION
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate
or door.
AVERTISSEMENT
FEATURES
For use with any Security✚
having an orange "learn" button.
ATTENTION
Personalized Password: Up to 10,000 possible
combinations. Password can be easily changed if desired.
Temporary Password: Can be added for visitors or
service persons. This temporary password can be limited
to a programmable number of hours or a programmable
number of entries.
Rolling Code: While your password remains constant
until you change it, the code between the Keyless Entry
and the receiver changes with each use, randomly
accessing over 100 billion new codes.
Operation: Opener activates when 4-digit password and
Enter button is pressed.
If wrong numbers are accidentally pressed, correction can
be made immediately. The Enter button will transmit only
the last four digits.
The Keypad will blink for 15 seconds after the password
is transmitted. During that time the Enter button can be
used to stop or reverse the door travel.
THE KEYLESS ENTRY BATTERY
WARNING
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
CAUTION
• If battery is swallowed, immediately notify doctor.
The 9 volt battery should produce
power for at least one year.
Replace when the keypad
illumination becomes dim.
Dispose of old batteries properly.
AVERTISSEMENT
ATTENTION
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
® garage door openers
Model 940-315CB Security✚
Wireless Keyless Entry
Instructions are Described and Illustrated Below
If you have a lighted push button that looks like the lighted
push button illustrated follow the instructions below.
1. Remove the cover from the Lighted
Door Control.
2. Enter a four digit personal
identification number (PIN) of your
choice on the keypad. Then press
and hold ENTER.
3. While holding the ENTER button,
press and hold the "A" button on the
Lighted Door Control.
4. Continue holding the ENTER and
"A" buttons while you press the "B"
button on the Lighted Door Control
(all three buttons are held).
5. Release buttons when the motor unit
lights blink. It has learned the code. If
light bulbs are not installed, two
clicks will be heard.
If you have a multi-function wall control follow instructions
below.
1. Enter a four digit personal identifica-
tion number (PIN) of your choice on
the keypad. Then press and hold
ENTER.
2. While holding the ENTER button,
press and hold the LIGHT button on
the Multi-Function Door Control.
3. Continue holding the ENTER and
LIGHT buttons while you press the
push bar on the Multi-Function Door
Control (all three buttons are held).
4. Release buttons when the motor unit
lights blink. It has learned the code. If
light bulbs are not installed, two clicks
will be heard.
If neither of the two programming instructions match your
type and style of opener follow instructions below.
Press and release the "learn" button on motor unit. The
learn indicator light will glow steadily for 30 seconds. Within
30 seconds, enter a four digit personal identification number
(PIN) of your choice on the keypad. Then press and hold
the ENTER button. Release the button when the motor unit
lights blink. It has learned the code. If light bulbs are not
installed, two clicks will be heard.
1
WARNING
WARNING
AVERTISSEMENT
AVERTISSEMENT
"A"
Button
"B"
Button
WARNING
WARNING
AVERTISSEMENT
AVERTISSEMENT
®