Bosch PCM 8 S Manual Original página 29

OBJ_BUCH-2325-003.book Page 29 Monday, October 24, 2016 11:12 AM
48 Saw-table extension (flexible)
49 Opening for flexible saw-table extension 48
(on the stationary saw-table extension 17)
50 Slider for laser unit
51 Fastening screw for insert plate
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Sliding Mitre Saw
Article number
3 603 M10 ...
Rated power input W
-1
No-load speed min
Laser type nm
mW
Laser class
Divergence of laser line
Base unit
Weight according to
EPTA-Procedure
01:2014 kg
Protection class
* Tool version with base unit
Permissible workpiece dimensions (maximum/minimum) see page 32.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Max. cutting width
Mounting hole diameter
Noise Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 94 dB(A); Sound power level
102 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 61029-1, EN 61029-2-9, EN 60825-1,
EN 50581:2012.
Bosch Power Tools
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch Power Tools GmbH
PCM 8 S
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
PCM 800 S PCM 8 ST
Assembly
... 1.. ... 1..
 Avoid unintentional starting of the machine. During as-
1200 1200
sembly and for all work on the machine, the power plug
4800 4800
must not be connected to the mains supply.
650 650
Delivery Scope
< 1 < 1
2 2
1.0 mrad 1.0 mrad
(full angle) (full angle)

–
low have been supplied:
– Sliding mitre saw with mounted saw blade
11.4 18.2*
– Dust bag 23
/II /II
– Stationary saw-table extension 17 (2 x),
Fastening screws 16 (2 x)
– flexible saw-table extension 48 (2 x)
– Material clamp 19
– Hex key 38
– Tilt-protector bar 30 with fastening screws 42
Additional components on PCM 8 ST (tool version with
mm 216
base unit)
mm 1.4–1.8
Base unit
mm 2 – Leg profiles F, C (4 of each)
– Connecting profiles E, D (2 of each)
mm 30
– Head profiles A, B (2 of each)
– Shim i (2 x)
Fixing set
– Carriage bolts base unit g (26 x)
– Flange nuts h (30 x)
– Fastening screws power tool j (4 x)
– Washers k (4 x)
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Additionally required tools (not in delivery scope):
– Box-end or open-end spanner (size 12 mm)
for assembly of the base unit
English | 29
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Please also observe the representation of the
delivery scope at the beginning of the operat-
ing instructions.
Before starting the operation of the machine
for the first time, check if all parts listed be-
1 609 92A 1KU | (24.10.16)