Kenwood ES630 Serie Manual De Instrucciones página 5

safety
● Never remove the filter holder whilst coffee is brewing or the coffee or steam
button is pressed - steam could shoot out and burn you.
● Don't get burnt by:
● ● hot parts, including the steam/hot water nozzle, cup warming tray, filter
holder and liquid coffee outlet.
● ● steam or hot water coming out of the steam/hot water nozzle or liquid
coffee outlet.
Keep children away from the machine. And never let the cord hang down
●
where a child could grab it.
● Never use a damaged machine. Get it checked or repaired: see 'service'.
● Never put the machine in water or let the cord or plug get wet - you could get
an electric shock.
Unplug:
●
● ● before filling with water
● ● before cleaning
● ● after use.
● Never leave the machine on unattended.
● Don't let the cord touch hot parts.
● Don't let infirm people use the machine without supervision.
● Don't let children play with this machine.
important
● Never use without water - the pump will burn out.
● Keep the machine above 0°C - otherwise any water in the machine will freeze
and cause damage.
● Only use the machine for its intended domestic use.
Never use without the drip tray and cup stand.
●
● Opening the steam knob will allow hot water to flow out of the steam/hot water
nozzle.
before plugging in
● Make sure your electricity supply is the same as the one shown on the
underside of your machine.
● Your machine complies with European Economic Community Directive
89/336/EEC.
before using for the first time
1 Remove all packaging.
2 Wash the parts: see 'cleaning'.
3 Flush the machine through with clean water: see 'before making coffee for the
first time'.
4 Wind excess cable around the cleats on the underside of the coffee maker.
know your Kenwood espresso machine
cup warming tray
tank lid
water tank
spoon
steam/hot water nozzle
liquid coffee/boiler outlet
button/indicator light for hotter coffee (
two cup dispensing button/indicator light (
OK indicator light ( )
steam/hot water button/indicator light (
one cup dispensing button/indicator light (
on/off button/indicator light (
steam/hot water knob
drip tray
float
cup stand
filter holder
filter emptying lever
filter for 1 cup dispensing or coffee pod
filter for 2 cup dispensing only
)
)
)
)
)
before making coffee for the first time
1 Make sure that the steam/hot water knob is closed by turning clockwise (don't
overtighten).
2 Lift out the tank, remove the lid and fill with cold water. Never fill above the MAX
level marked. Alternatively remove the lid and fill the tank whilst in position on
the coffee maker.
● We recommend using filtered water from a Kenwood water filter as it produces
better coffee and reduces limescale. Never use fizzy water.
Re fit the tank. Make sure that it is correctly located and apply light pressure if
●
necessary to ensure the valve at the bottom of the tank connects with the
bottom of the machine.
Note it is normal for water to remain in the compartment under the tank. This
can be dried using a sponge.
Important
Never operate the machine without water in the tank. Top up as
soon as the level gets low.
3 Swing out the steam/hot water nozzle and put a jug underneath.
4 Attach the filter holder to the machine by positioning it under the liquid
coffee/boiler outlet and turning to the right
5 Switch on by pressing the on/off button (
indicate the unit is warming up. (Wait until the light stops flashing indicating that
the correct temperature is reached).
6 Press the two cup dispensing button (
into the bowl. (It will automatically switch off after 2 cups have been dispensed).
7 Turn the steam/hot water knob anti-clockwise and allow two cups of water to
run into the jug.
8 Turn the steam/hot water knob off by turning clockwise.
9 Repeat these steps once more.
● If you haven't used the coffee maker for a few days repeat this procedure.
preheating the coffee machine
To ensure your espresso coffee is dispensed at the right temperature it is
essential that the coffee unit is pre heated.
1 Check that the steam/hot water knob is firmly closed (turn clockwise) and that
there is water in the tank.
2 Fit the desired filter into the filter holder (without coffee), make sure the tab on
the filter fits into the slot on the filter holder. Attach to the machine by
positioning it under the liquid coffee/boiler outlet and turning to the right
Ensure it is firmly located.
3 Press the on/off button (
before preparing the coffee. To speed up the pre-heating operation carry on
with the following procedure.
4 Position a cup under the filter holder. If you use the same cup that the coffee
will be served in it will be preheated. Alternatively the cups can be pre heated
on the cup warming tray.
5 When the OK light stops flashing, press the 1 cup dispensing button (
allow water to flow out. It will switch off automatically after 1 cup has been
dispensed.
6 Remove the filter holder and empty out the hot water and proceed to make
coffee using either ground coffee or coffee pods. It is normal for a small puff of
steam to be given off when removing the filter holder.
2
. Place a bowl underneath.
), the OK indicator light will flash to
) and wait until two cups of water runs
) to switch on the machine and wait for 15 minutes
.
) and