Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
2003-08 Fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24814F
Wrenches: 17mm, 19mm
For vehicles with appearance
panel:
Remove appearance panel which
covers the trunk pan.
(2)10mm
Remove the plastic rivets that
fasten the fascia tabs to the
vehicle. Note: Remove the center
of the rivet with a screwdriver.
Rivets to be reinstalled.
Return appearance panel and
fasteners to vehicle owner.
1 1 1 1
Qty. (4)
Hex Bolt, M12 X 1.25 X 35 CL8.8
2 2 2 2
Qty. (4)
Conical washer ½"
If present, remove the tie down brackets from vehicle frame rail. Return bolts and tie down bracket to owner.
1.
Raise hitch into position and install fasteners as shown above.
2.
Tighten all fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Tighten all M12 CL8.8 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2014 Cequent Performance Products
Printed in Mexico
Installation Instructions
Toyota Corolla
2009 Fascia
Drawbar Kit:
3593
Drawbar must be used in
the RISE position only.
Note: Fasteners typical
both sides
Frame rails
Existing weldnuts
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
3 3 3 3
Qty. (4)
Flat washer ½"
Sheet 1 of 3
24814N
Part Numbers:
24814
60200
77186
Manufacturer's Rating or
Accessory Rating
Wiring Access Location: PC3, 4
3
Note: 2014
Use flat washers (items 3)
as needed as spacer if
trunk reinforce interferes
with hitch installation.
2
1
1-14-14
Rev. B
Form F206 Rev A 5605
A
Publicidad
Manuales relacionados para Cequent Performance Products 24814
Resumen de contenidos para Cequent Performance Products 24814
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24814N 1-14-14 Rev. B 2008, 2014 Cequent Performance Products Printed in Mexico Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24814N 1-14-14 Rev. B 2008, 2014 Cequent Performance Products Form: F205 Rev A 5-6-05 Imprimé au Mexique...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2008, 2014 Cequent Performance Products Hoja 3 de 3 24814N 1-14-14 Rev.