Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Tin Snips
Fastener Kit: 24811F
Wrenches: ¾"
Drill Bits: 3/8", 1" Hole Saw
j
k
Fasteners typical both
Sides of vehicle
j
Hex Bolt – ½-13 x 1.50 GR5
Qty. (2)
k
Block – ¼ x 1 x 2
Qty. (4)
l
Carriage Bolt – ½-13 x 1.75 GR5
Qty. (2)
Remove passenger's side exhaust hanger by removing (2) bolts which attach exhaust hanger bracket to frame. Retain bolts for reinstallation.
1.
2.
Raise hitch into position and temporarily attach using only tow hook mounting fasteners.
3.
Mark exhaust heat shield at each frame bracket flange for trimming to allow flange to sit flat against vehicle frame.
4.
Using holes in frame bracket flanges, mark hole locations on frame rails.
5.
Take down hitch. Drill access holes in frame rails in areas marked in step 4 (See figure 2)
Reverse fishwire ½" carriage bolts and blocks thru access holes as shown in figure 3.
6.
7.
Raise hitch back into position, being careful not to push carriage bolts back into frame. Secure with fasteners as shown in Figure 1. Tighten all
½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Reattach passenger's side exhaust hanger bracket with existing fasteners. Because hanger bracket will overlap hitch frame bracket, it will be
8.
necessary to space down exhaust hanger using ¼ x 1 x 2 blocks as shown above.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
Fascia
Drawbar Kit:
3593
(Sold separately)
Drawbar must be used in the
l
Rise position only.
m
Vehicle Frame Rail
Vehicle Tow Hook
n
o
n
o
Exhaust hanger
bracket
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Ft.-Lb. (102 N*M)
Tighten all M6 fasteners with torque wrench to 62 In.-Lb. (7 N*M)
Volvo C30
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8) Max Tongue Weight
Wiring Access Location: PC3, PC4
A. Insert bolt and
Block into frame
k
Frame
Bracket
Flange
Existing exhaust
Hanger bolts
m
Qty. (2)
Block - ¼ x 1 x 3 (Square Hole)
n
Lock Washer – ½"
Qty. (4)
o
Hex Nut – ½-13
Qty. (4)
Sheet 1 of 3
24811N
Part Numbers:
Manufacturer's Rating or
B. Align block on
Access hole
Figure 3
Reverse fishwiring procedure
5/8" (16mm)
Heat shield
Trimmed for
frame bracket
flange
Hole location
Marked in
step 4
Figure 2
Drilling of Access Holes
10-09-15
Form F206 Rev A 5605
24811
77182
60897
C. Pull bolt thru
block
5/8" (16mm)
3/8" hole (2)
Drill first
1" dia. – drill
After 3/8" holes
Are drilled.
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24811
Resumen de contenidos para Cequent Performance Products 24811
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2008, 2015 Cequent Performance Products – Printed in Mexico Sheet 1 of 3 24811N 10-09-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24811N 10-09-15 Rev. B 2008, 2015 Cequent Performance Products - Imprimé au Mexique Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. Sheet 3 of 3 24811N 10-09-15 Rev. B 2008, 2015 Cequent Performance Products - Impreso en México Form F206 Rev A 5605...