Technical Data; Replacement Of The Battery - Simu 2008369 Manual De Instrucciones

GB HZ WALL TRANSMITTER 1 channel
SAS. au capital de 5 000 000 € - Z.I. Les Giranaux - BP71 - 70103Arc-Les-Gray CEDEX - RCS GRAY B 425 650 090 - SIRET 425 650 090 00011 - n
a y
P rogramming the transmitter with an existing installation
1.1. Open the memory of the motor using its individual control transmitter:
- Press the Prog. Key for about 3 sec. on the motor's individual contrai transmitter, the motor
rotates by about 0,5 sec in one direction, then in the other.
1.2. Then validate the operation from the new transmitter to be programmed:
- Press the Prog. key for about 1 sec. on the new transmitter, the motor rotates for about 0,5
sec in one direction, then in the other.
- For group contrais from the new transmitter, repeat operations 1.1 and 1.2 for each motor of the group.
- For main contrais from the new transmitter, repeat operations 1.1 and 1.2 for each motor of the installation.
- To delete a transmitter from the memory of a motor, perform operation 1.1 with a programmed transmitter, then perform
m
operation 1.2 with the transmitter to be deleted.
For more complete information about programming, please refer to the instructions of the motor used.
Il
m
Recording and controling intermediate position (P.I.)
Refer to Hz motor instructions to make sure it has this feature.
Recording:
- Move the motor to the wanted
position.
- Press 5 seconds on the STOP key.
The motor will run for 0,5 second in
one direction and then in the other.
D

Technical data

- Compatible with motors & receivers
- Wireless switch/class Ill - Protection Index: IP30
- Radio frequency: 433,42 MHz
- Maximum transmission lime: 1 O seconds
-Ambient temperature of use : -10T60 (-10'C / +60'C)
- Storage temperature: -30'c to + 70'C
- Transmitter range: 15m throught 2 concrete walls in normal
pollution condition).
- Power: 3V lithium battery typeCR 2430. Lifetime ± 3 years when
a
4 pressures of 1 s. / day.

Replacement of the battery

- Power supply is not required for saving data.
- Data need not be programmed once again when the cell is changed.
- Do not recharge the battery.
- Please separate and dispose of the appliance, batteries and used batteries in a dedicated recycling point.
C �
Simu hereby warrants that this product is in compliance with the essential requirements and other relevant provisions of European Direc-
,;;. lives a licable to the Euro ean Union: 2014/53/UE. A Declaration of Conformit is available al www.simu.com.
Controling:
- Press the STOP key for 0,5
second. The motor runs to
the intermediate position.
(•)
s1mu-Mz
teclmology
- Keep away from children
- Do not position the transmitter near metal in order to ensure ils
good working (reduced range).
-A radio appliance using the same frequency (for example : hi-fi
radio headphones) may deteriorate our product's performance.
- Do not immerse the product, avoid splashing of liquids.
- Do not use abrasive products or solvents to clean the product.
- Frequency range: 433,050 MHz - 434,790 MHz F: 433,420 MHz
- Max power used: ERP< 10 mW
5123093A
Read carefully these instructions
before any use.
° T.V.A CEE FR 87 425 650 090
STOP�.�
't
P.I. (§2)1:9"
- ��1» 1
PROG
> 3 s
=
PROG
�+)
=
:S1s
o.ss(]--
�]zl
CR2430 -
1111'1
li
li
l
l
1111