Radio Operation; Usb Operation; Bluetooth Operation - Denver BTB-410 Guía Del Aparato

There's a light bar above the handle, the white light on when the Blue/Red LED on constantly, the bar will keep flashing when LED in flashing mode. Press
and hold the EQ/LIGHT button until OFF shows on the display to turn it off together with the disco light.

RADIO OPERATION

Listen to FM radio broadcasts. Press the FUNCTION/
Eng-2
Note: In order to get the best reception, extend the FM wired ANT. on the rear cabinet to its full length before use. If stereo signal is received, the display will
show the "ST" indicator.
TUNING TO A RADIO STATION
If you know the station frequency that you want to tune to directly:
•
Tune to a station by pressing the
•
Press and hold the /TUN.+ or
AUTO PRESET MEMORY/SCAN
To scan for stations within reception range and save them to preset memory automatically, press and hold the PLAY/PAUSE/PAIR/SCAN button. After the
unit is finished scanning, the unit will automatically tune to preset number 1 (P01).
MANUAL PRESET MEMORY OPERATION
Choose which stations to save in preset memory instead of scanning automatically.
1.
Use the /TUN.+ or /TUN.- button to tune to the station that you want to save as a preset (e.g., 93.1).
2.
Press the P-MODE/M./ECHO button. "P01" will flash on the display to indicate that you are saving the station as Preset Memory 01. (To
change the preset memory number, press the 10/M./FOLD.+ or 10/M./FOLD.- buttons.)
3.
Press the P-MODE/M./ECHO button to finish saving the station (e.g., P01 is now set to 93.1).
4.
To save another station, repeat steps 1 to 3. You may save up to 30 FM stations.
To tune to a preset station:
•
To tune to the next preset station, press the 10/M./FOLD.+ button.
•
To tune to the previous preset, press the 10/M./FOLD.- button.

USB OPERATION

1.
Press the FUNCTION/
2.
Plug the USB memory stick to the USB port on top of the unit. Playback will start automatically.
3.
To pause playback, press the PLAY/PAUSE/PAIR/SCAN button on unit. The playing time will flash on the display.
4.
To resume playback, press the PLAY/PAUSE/PAIR/SCAN button again.
5.
To select a desired track, press the
will start play automatically.
6.
To search for a particular passage during playback, press and hold the
until desired point (passage) appears, then release the button for normal playback mode.
Eng-3
To select a song which track number exceeds 10, press the 10/M./FOLD.+ or 10/M./FOLD.- button each time to skip forward/backward 10 tracks, then
press the /TUN.+ or /TUN.- button to select desired track.
7.
To select a desired folder (if the USB contains more than one folder), press and hold the 10/M./FOLD.+ or 10/M./FOLD.- button each time to skip
forward/backward a folder, then press the
Important: The USB port is intended for data transfer only, other devices cannot be used with this USB connection. The use of USB extension
cords is not recommended. Don't plug the USB from the unit when playing or reading the USB device.
REPEAT PLAY
You can play one track or all tracks on the USB repeatedly.
To repeat a single track
1. Press P-MODE/M./ECHO button on unit during play, the display will show " " and the current track will be played over an over again.
2. To cancel repeat play, press P-MODE/M./ECHO button on unit until " " disappears from the display.
To repeat all the tracks
1.
Press P-MODE/M./ECHO button on unit until the "
2.
To cancel repeat play, press the P-MODE/M./ECHO button on unit until "
To repeat the folder (only for USB which contains more than one folder)
1.
Press the P-MODE/M./ECHO button on unit until "
2.
To cancel repeat play, press the P-MODE/M./ECHO button on unit until "
RANDOM PLAY
Press the P-MODE/M./ECHO button on unit in play mode till the "RAND" shows steadily on the display, the random play will start from next track
automatically. Press the P-MODE/M./ECHO button on unit again until the "RAND" disappears from the display to cancel.

BLUETOOTH OPERATION

1.
Press the FUNCTION/ button on unit to switch to BLUETOOTH function, the LCD will display "bt" and the pair indicator will flash at high speed.
2.
Turn on the Bluetooth function on the device, scan the unit "BTB-410" and connect, then input the password 0000 if required, the pair indicator keep
light up to indicate connection done, and the display will show "bt". Press Play to start playback.
button on the unit to choose FM mode, the display will read the radio frequency.
/TUN.+ or /TUN.- button repeatedly. The station frequency will show on the display.
/TUN.- button to quick scan the stations that with strong signal.
button on unit to select USB mode.
/TUN.+ or /TUN.- button respectively during playing until the desired track appears on the display. The unit
/TUN.+ or /TUN.- button to select desired track.
" shows steadily on the display, all tracks on the USB will be played over and over again.
FOLDER" shows steadily on the display, the current folder will be repeated over and over again.
/TUN.+ or /TUN.- button to scan the current playing track at high speed
" disappears from the display.
FOLDER" disappears from the display.
3