KIKKA BOO BONNE NUIT Instrucciones De Uso página 8

WARNINGS
1. Please read this manual carefully before use, and keep the manual for future reference. If not in accordance with the operation of this manual may
cause security risks for children.
2. Children must use the product under the supervision of an adult.
3. If any part of the small bed is damaged, torn or missing, do not use.
4. Ensure that all users are familiar with the operation of the product, to ensure that products can be easily opened and closed. If the product does not
open or collapse properly, do not force it. Please read the product manual carefully and use the correct method.
5. Before using the small bed, please carefully check all parts are installed and adjusted correctly and all devices are locked in a stable state.
6. When the bed is stitched to the big bed, make sure to use safety straps to prevent baby fall bacause of the shaking bed.
7. Avoid placing the bed near heat or dangerous goods.
PARTS
1. Washable mattress 2. Fabric cover 3. Bed board 4. Main parts 5. Supporting tube 1 6. Supporting tube 2 7. Handrail tubes 8. Safety strap 1 9. Safety
strap 2 10. Carry bag
ASSEMBLY
Step 1: Open the main parts ,and place it in stand position, like the Picture A; Then insert the support tube 2 into the main part plastic and make sure
the supporting tube is rmly connected. Showed as the Picture B.
Step 2: Insert the supporting tube 1 into the main part of mini playard. When you hear a click sound, the supporting tube 1 is completely installed. As
picture C.
Step 3: To install the fabric cover ,get the tubes go through the fabric cover like the Picture A. After the fabric covered the handrail tube, pull the zipper
follow the red arrow direction as the picture B.
Step 4: Get the other part of the handrail tube go through the fabric cover, like thepicture A. Then connect the two part of han-drails together like
Picture B, and make sure the two parts are rmly xed. Pull the zipper at last.
Step 5: Put the bed board into mini playard, and put the safety strap through the hole like picture A . Then x the bed board withsupport tube together
and make sure the two parts are rmly xed like picture B.
Step 6: After putting the mattress inside the mini playard, the installation iscompleted. Press the botton of two sides, you can adjust the mini playard to
the lowest position as Picture A. There are 3 positions for you to adjust the heights.
FUNCTIONS
ROCKING FUNCTION:
When you open the rocking system part, the mini playard will keep in stable position, like Picture A . When take back the rocking system part, the mini
playard will change to rocking status, like picture B.
STITCHING BED FUNCTION:
As shown in picture A, the armrest side is removable, so you can put it as the picture B shows, The main function is to splice to mother's bed. In this
case,it is easy for mother to take care of the baby and feed timely at night.
LEGS STRETCH FUNCTION:
As red circles show in picture , the left and right standing tube legs can be stretched at both ends, as shown in picture B. The main function of the
telescopic function is when the bed in spiced to the bed, the legs can be free to stretch to t all types of large beds. At the same time it can prevent baby
rollover when it is raised to the toppest level under shaking.
SAFETY STRAP FUNCTION:
Used when the bed and bed stitching xed small bed and bed, the function of the most important, be sure to use a xed band, to ensure a good xed
before using the stitching function.
CO-SLEEPING MODE( FIXING TO THE ADULT BED):
Step 1. Open the zippers of the side wall of !he cot al the both sides of the mesh. Picture 3.1
Step 2. Catch the upper support lube (2) at !he bolh ends, press the buttons from lower side and pull out Picture 3.2; 3.3 Insert the both ends of the
support lube in !he openings al the bolh sides of the fabric. Picture 3.4
Step 3. Attach the both ends of attaching belts for the bottom of the cot( Picture 3.5). Pull out the belt for adjusting of !he length ( Picture 3.6;3.7 ). Plase
the attaching belt under !he adult mattress bed and x the attaching hook rmly for the base of the bed( Picture 3.8;3.9)
WARNING! Due to the risk of su ocation, adjust the height of the col so !hat !he edge of !he adult bed is above the edge of !he fold at a maximum height
of 2 cm (Picture 3.10 ).
WARNING! Due to the risk of falling, there should be no gap between the underside of the product and the mattress on the adult bed !!! Picture 3.11.
ENGLISH