KBS Joy Serie Indicaciones Para El Uso página 8

GB USER MANUAL - FULL CUBE ICE MACHINE
Many thanks for selecting our product and we wish you a long and problem free use for many years. In every complain or communication about the
ice machine with the manufacturer or the distributor indicate the model and serial number.
CAUTION: HANDLE CAREFULLY TO AVOID DAMAGE TO THE REFRIGERATING CIRCUIT
CAUTION: FOR INSTALLATION IN A KITCHEN, ADD THE EQUIPOTENTIAL EARTH SYSTEM
CAUTION: DURING OPERATION OF THE ICE MACHINE, PAY ATTENTION TO THE MOVING MECHANICAL PARTS
CHECK AT DELIVERY
1) The packing of damages.
2) The delivered ice machine with the purchase order.
3) The ice machine is not damaged during transport and no parts are missing.
In case of damages or missing parts, report immediately to the delivering carrier or your supplier.
INSTALLATION PROCEDURE
1) Carefully read all the applicable national regulations for connection to the water supply network.
2) The ice machine is not suitable for outdoor use.
3) The ice machine is not suitable for installation in areas where jets of water may be used.
4) The ice machine must be installed only in places where operation and maintenance are performed by qualified personnel.
5) Only persons with knowledge and practical experience of the ice machine, in particular as regards safety and hygiene standards, should be allowed
access to the service area.
6) The ice machine is not designed for use by persons (including children) with reduced physical, sensorial or mental capacity, or with no experience
or knowledge, unless they are supervised or instructed in use of the equipment by a person responsible for their safety.
7) The weighted sound pressure level "A" is below 70 dB.
8) Remove the ice machine from its packing and place it in the desired position, ensuring that it is perfectly horizontal (feet are adjustable) and well
away from heat sources. Also the ambient must be ventilated.
9) Air inlets and outlets should be kept at least 20 cm from walls.
10) Ambient temperature must not be lower than 5°C or higher than 35°C for a satisfactory yield and to prevent freezing.
11) Power supply must be 230 V - single phase. The maximum voltage variation permitted is ±6%. It is advisable to protect the main switch by means
of a fuse.
12) An earth terminal is essential.
13) Drink water supply pressure must not be less than 1 bar (kPa) and not higher than 6 bar (600 kPa). Water temperature must be between 5°C
and 20°C for a satisfactory yield.
14) Drink water is supplied through a flexible hose (provided with the machine) which should be connected to the water mains by means of its 3/4"
BSP threaded connection. Only with drink water. When replacing the pipe, the gaskets should also be replaced.
15) The drain pipe must have a drop of at least 15%. If the drain is far from the ice machine use a larger diameter hose, ensuring that it is not twisted
or kinked at any point. Note, use an open vented drain.
16) If the power supply cable is damaged, it must be replaced by the manufacturer or its technical support service or in any case by a person with a
similar qualification, in order to prevent all risks.
ATTENTION: DURING THE INSTALLATION OF THE MODULAR ICE MACHINES THE AUTHORIZED SERVICE COMPANY HAS TO
PLACE THE BIN THERMOSTAT FEELER AT THE RECOMMENDED POSITION OF THE ICE STORAGE BIN.
STARTING UP
After checking all the previous points:
1) Turn the water supply tap on.
2) Place the plug in the power socket with main switch. If the unit is only equipped with an electrical cord for power supply, the authorized service
company must connect the lead wires to an electrical plug that corresponds to the local electrical requirements or to a separate two poles disconnect
switch with opening between the contacts of minimum 3 millimeters, very close to the ice machine to be reached easily and promptly.
3) Turn on the main switch. This operates through a timer mechanism and the ice machine will start after approximately 3 minutes with the ice
production cycle.
4) After stopping the machine operation by the main switch, wait at least 5 minutes before re-starting it again.
OPERATION
The cycle starts with the defrosting phase, i.e. the inlet of the water from the mains, the water pump is inactive, the compressor is in operation and the
hot gas valve is open. At the end of this phase the water inlet solenoid valve and the hot gas valve close themselves automatically and the pump starts.
Now the ice production phase starts. The pump pumps the water from the water bin through a manifold and a series of jets. Each jet feeds a series of
bowls which together constitute the evaporator. The water sprayed by the jets forms a series of layers of cristalline ice on the evaporator, thus forming
the ice cube. When the evaporator reaches the required temperature and ice cube dimension (run by an evaporator thermostat and a timer), the defrosting
phase starts automatically (pump inactive, compressor in operation, water inlet and hot gas valve open). The ice cubes are released and fall into the
ice storage bin. The excess water flows out through the overflow connection. After the ice cubes have fallen a new ice production cycle starts. This is
repeated until the ice storage bin is filled up and the ice machine is stopped automatically by the bin thermostat. After the ice has been removed the
ice machine will start again the cycle from the defrosting phase automatically (bin thermostat).
CAUTION: ICE IS FOR HUMAN CONSUMPTION,WASH YOUR HANDS BEFORE HANDLING, KEEP MACHINE BIN LID CLOSED
AND ENSURE REGULAR CLEANING OF ALL UTENSILS AND PARTS IN CONTACT WITH THE ICE.
MAINTENANCE AND CLEANING BY THE USER - DISCONNECTING POWER AND WATER SUPPLY.
1) The ice machine cannot be cleaned with a jet of water.
2) Take out the spray bar, clean it in warm water mixed with a de-scaling solution(minimum dose) and rinse it under running warm water.
3) Clean the ice storage bin, using a detergent diluted in warm water and rinse it with warm water.
4) Clean the bodywork with a soft damp cloth with a specific product.
ROUTINE MAINTENANCE (EVERY 6 MONTHS) - AUTHORIZED SERVICE ONLY
1) Clean the solenoid valve filter and the pump filter in the water bin.
2) Clean the condenser wins with a soft brush each month.
3) Clean the ice production system and the storage bin.
4) In the event of lengthy idle periods clean all the parts of the ice machine.
This appliance conforms to EEC Directive EEC 2006/95 - EEC 2006/42 and EEC 2004/108 on radiointerference.
6