Cleaning And Maintenance - Asist AE5PO85 Instrucciones De Uso

bestos!
Place the base on the workpiece surface and cut it
with continuous constant pressure. If the saw blade
jams, switch off the saw immediately. Use suitable
tools to enlarge the hole and then remove the saw
blade.
When you have finished working, switch off the saw
and wait until it has come to a complete stop.
Metal cutting
-! Always use only the saw blade for metal materials
to cut metal materials!
- Your multi-purpose saw can be used to cut thin fer-
rous and non-ferrous metal materials such as copper,
brass, aluminum, etc., see recommended materials.
- It is expedient to clamp the cut narrow or soft sheet
metal on both sides with softwood or plywood boards,
which will ensure a straight and undeformed cut, as
all materials are cut together.
- When cutting metal, do not apply excessive pres-
sure to the saw, as this will reduce the life of the saw
blade excessively and avoid possible damage to the
motor. Cutting sheet metal materials takes longer
than cutting relatively much bulkier wooden objects,
so don't be tempted to speed up the cutting process
by increasing the load / pressure on the saw.
- It is advisable to coat a line of the expected cut on
metallic materials with a thin layer of oil before star-
ting to cut. This will reduce cutting friction and saw
blade wear.

CLEANING AND MAINTENANCE

! Before cleaning and maintenance, always unplug
the tool.
Your device does not need any additional lubrication
or maintenance. There are no parts that you can
repair.
Never use water or chemical cleaners to clean your
equipment. Just wipe it with a dry cloth.
Keep the air intake grille clean.
If you see a very faint spark in the engine compart-
ment, your tool is OK. Increased sparking is a fault in
the engine.
- Never clean any part of the tool with a hard, sharp
or rough object.
Long-term storage of hand tools
Do not store the tool in a place where the temperature
is high.
If possible, store the tool in a place with a constant
temperature and humidity.
SPECIFICATIONS
Power supply values 230 V ~ 50 Hz
Power consumption 850W
No-load frequency
Weight 2.5 kg
Max. depth of cut: wood 160 mm
Max. cutting depth: metal 8 mm
Protection class / II
SDS clamping
0-2800 min-1
Swivel handle
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 91 dB (A) KpA=3
LWA (sound power) 102 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound pressure
exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN
60745:
22,2 m/s2 K=1.5
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
the power tool for the purpose for which it has been
designed and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in all
operating modes, e.g. the time when the power tool is
switched off except for the operation time, and when
it idles, i.e. performs no work. This may substantially
decrease the exposition level during the whole operat-
ing cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVIrONmENTAL PrOTECTIONWASTE mA-
NAgEmENT
Power tools, accessories and packaging should be
provided for recycling and not to harm the environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
43