Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 3

Enlaces rápidos

INSTRUCTIONS & PARTS LIST FOR NO. 2 SERIES 90° & 45° ANGLE DRILLS
Read and understand "Safety Instructions For Air Tools" and these instructions before operat-
Tools left connected to the air supply while making adjustments, changing accessories, or doing any mainte-
Always remove tool from air supply and activate trigger to bleed air line before making any adjust-
ments, changing accessories, or doing any maintenance or service on tool.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter,
pressure regulator, and lubricator will insure maximum output and life of tools.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 3/8" (10 mm) I.D. Extension hoses should be at least 1/2" (13 mm) I.D. Use couplings
and fittings with at least 3/8" (10 mm) I.D.
LUBRICATION
An airline lubricator, set to deliver 2 to 4 drops per minute, is recommended. If a lubricator is not used, add .04 oz. (1.2 cc,
12 to 15 drops) of SIOUX No. 288 air motor oil into the air inlet twice a day.
Lubricate the planetary gear assemblies with 1/4 oz (7 gm) of SIOUX No. 298A grease after every 100 hours of operation.
Lubricate the angle head with 0.01 oz (0.3 gm) of SIOUX 1198 grease after every 8 hours of operation.
GENERAL OPERATION
Depress the lever to start the tool. A speed control adjusting screw is located on the motor housing opposite the lever.
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
A1210, A1300, A1310, A1320, A1510, AY1210, AY1300, AY1310, AY1320, AY1510 including 45, AH suffixes
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
June 1, 2003
Murphy, North Carolina, USA
Date and place of issues
ing this tool.
nance or service on tool can start unexpectedly.
Tools starting unexpectedly can cause injury.
SOUND AND VIBRATION READINGS
Catalog No.
Sound Pressure dBA
A1210
78.4
A1300
78.4
A1310
78.4
A1320
78.4
A1510
78.4
AY1210
78.4
AY1300
78.4
AY1310
78.4
AY1320
78.4
AY1510
78.4
*prt PN8NTC1
DECLARATION OF CONFORMITY
EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
Gerald E. Seebeck
President
Sioux Tools Inc.
Name and position of issuer
Sound Power dBA
Vibration m/s
90.2
Less than 2.5
90.2
Less than 2.5
90.2
Less than 2.5
90.2
Less than 2.5
90.2
Less than 2.5
90.2
Less than 2.5
90.2
Less than 2.5
90.2
Less than 2.5
90.2
Less than 2.5
90.2
Less than 2.5
*prt PN8NTC1
*per ISO8662
Signature of issuer
1
Form ZCE469A
Date 2003June20/D
Page 1 of 12
2
Printed In U.S.A.

Publicidad

Tabla de contenido
loading

Resumen de contenidos para SIOUX A1210

  • Página 1 *per ISO8662 DECLARATION OF CONFORMITY We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products A1210, A1300, A1310, A1320, A1510, AY1210, AY1300, AY1310, AY1320, AY1510 including 45, AH suffixes to which this declaration relates are in conformity with the following standard or standards or other normative document or documents: EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1...
  • Página 2: Allgemeiner Betrieb

    *per ISO8662 KONFORMITÄTSERKLÄRUNG Wir, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, erklären hiermit alleinverantwortlich, daß die Produkte A1210, A1300, A1310, A1320, A1510, AY1210, AY1300, AY1310, AY1320, AY1510 Einschließlich 45, AH Anhänge auf die sich diese Erklärung bezieht, mit den Anforderungen der folgenden Standards oder Normen oder Dokumenten übereinstimmen: EN 792 (Entwurf) EN 292 Teile 1&2, ISO 8662, Pneurop PN8NTC1...
  • Página 3: Suministro De Aire

    Se recomienda un lubricador de tubo de aire que distribuya de 2 a 4 gotas por minuto. Si no se utiliza el lubricador, agregue 0,04 oz (1,2 cc, 12 a 15 gotas) de aceite para motores neumáticos SIOUX No. 288 en la toma de aire, dos veces al día.
  • Página 4 *secondo ISO8662 CERTIFICAZIONE DE CONFORMITA' La Sioux Tools, Inc, con sede al 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, solennemente dichiara sotto la propria e sola responsabilità che i prodotti A1210, A1300, A1310, A1320, A1510, AY1210, AY1300, AY1310, AY1320, AY1510 inclusi i modelli con suffisso 45, AH...
  • Página 5: Lubrification

    Il est recommandé d’utiliser un lubrificateur d’air délivrant 2 à 4 gouttes d’huile par minute. En l’absence de lubrificateur, ajoutez deux fois par jour 1,2 ml d’huile SIOUX de référence 288 (0,04 once, soit 12 à 15 gouttes) dans l’arrivée d’air.
  • Página 6: Slang En Koppelingen

    Het is aanbevolen om een persluchtsmeersysteem te voorzien en dit af te stellen op 2 tot 4 druppels smeervloeistof per minuut. Is dit niet mogelijk, dan moet er dagelijks 0,04 oz (1,2 cc, 12 tot 15 druppels) persluchtmotorolie, type SIOUX N°...
  • Página 7 *enligt ISO8662 FÖRSÄKRAN OM ÖVERENSSTÄMMELSE Vi, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, förklarar under eget ansvar att produkterna A1210, A1300, A1310, A1320, A1510, AY1210, AY1300, AY1310, AY1320, AY1510 innefattande suffixerna 45, AH suffixes som denna försäkran gäller uppfyller följande standard eller standarder eller andra normgivande dokument:...
  • Página 9 PARTS LIST FOR NO. 2 SERIES 90° & 45° ANGLE DRILLS MOTOR ASSEMBLIES Fig. Part Name Fig- Part Name 14734 Gasket 19159 Gear—Pinion (5200 RPM) 10220 Bearing—Ball 14291 Ring—“O” 13161 End Plate—Rear 14350 Valve 10230 Bearing—Ball 25957 Washer 07140 Screw (4)* 43462 Ass'y—Valve 30062 Pin (2)* 21429 Spring...
  • Página 10 PARTS LIST FOR 90° ANGLE HEAD ASSEMBLY Fig. Part Fig. Part Description Description 65248 Bushing—Bearing 65242 Shim—.005" (Order Quantity As Needed) 2. 67495A Gear—Set (1/4"-28 Th’d) 65244 Housing—Angle Drill (Includes Figure 3, 5, 6, 7, 9) 10257 Bearing—Ball 67496A Gear—Set (#10-32 Th’d) 65243 Nut—Retaining (Includes Figure 3, 5, 6, 7, 9) 65143 Nut—Jam...
  • Página 11 PARTS LIST FOR 45° ANGLE HEAD ASSEMBLY Fig. Part Description 65238 Bushing—Flange 65246 Pin (2)*(Set of 22) 65236 Gear—Collet (1/4–28 Th’d) 65264 Gear—Collet (#10–32 Th’d) 65538 Gear—Collet (9/32"–40 Th’d) 30375 Fitting—Grease 65237 Housing—45° 65235 Pinion 65245 Retainer—Bearing 65242 Shim—.005" (Order Quantity As Needed) 65244 Housing—Angle Drill 10257 Bearing—Ball 65243 Nut—Retaining...
  • Página 12 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Der durch Elektrosanden, -sägen, -schleifen und -bohren sowie durch andere Bauarbeiten anfallende Staub enthält Chemikalien, die nachweislich Krebs sowie Geburts- bzw. andere Fortpflanzungsschäden hervorrufen.

Este manual también es adecuado para:

A1300A1310A1320A1510Ay1210Ay1300 ... Mostrar todo

Tabla de contenido