Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INSTRUCTIONS & PARTS LIST FOR
8000ES, 8005ES, & 8050ES
GENERAL SAFETY RULES
WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result
in electric shock, fire, and/or serious personal injury.
SAVE THESE INSTRUCTIONS.
WORK AREA
1.
Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
2.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks, which may ignite the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a power tool. Distractions can
cause you to lose control. Protect others in the work area from debris such as chips and sparks.
Provide safety barriers or shields as needed.
ELECTRICAL SAFETY
4.
Double insulated tools are equipped with a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet.
Do not change the plug in any way. Double insulation
grounded power cord and grounded power supply system.
5.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigera-
tors. There is increased risk of electric shock if your body is grounded.
6.
Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
7.
Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet.
Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords
immediately. Damaged cords increase the risk of electric shock.
8.
When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W".
These cords are rated for outdoor use and reduce the risk of electric shock.
PERSONAL SAFETY
9.
Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in serious personal injury.
10.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught
in moving parts.
11.
Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger
on the switch or plugging in tools with the switch on invites accidents.
12.
Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left
attached to a rotating part or the tool may result in personal injury.
13.
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the tool in unexpected situations.
14.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat,
or hearing protection must be used for appropriate conditions.
eliminates the need for the three wire
1
Form Z578
Date 1-02/D
Page 1 of 20
Printed In U.S.A.

Publicidad

Tabla de contenido
loading

Resumen de contenidos para SIOUX 8000ES

  • Página 1 Date 1-02/D Page 1 of 20 INSTRUCTIONS & PARTS LIST FOR 8000ES, 8005ES, & 8050ES GENERAL SAFETY RULES WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.
  • Página 2 Contact with a “live” wire will make exposed metal parts of tool “live” and shock the operator. Maintain warning label. SPECIFICATIONS SYMBOLOGY Catalog Volts No Load Twist Drill Double Insulated Capacity in Steel Canadian Standard Association 8000ES 0-1300 3/8" Underwriters Laboratories, Inc 8005ES 0-2500 3/8" 8050ES 0-750 1/2" Underwriters Laboratories, Inc (Canada/United States)
  • Página 3 Chuck removal Open chuck jaws to maximum capacity. Remove retaining screw on tool by turning it in a clockwise direction (screw has a left-hand thread). Insert the shorter end of a 1/4” or greater hex key into chuck and tighten. Place tool on its side and hold firmly.
  • Página 4: Extension Cords

    Do not use a damaged tool. Tag damaged tools “DO NOT USE” until repaired. Repairing Tool If your tool is damaged, return the entire tool to the nearest authorized Sioux Tools service center. ACCESSORIES Recommended accessories are available at extra cost from you local service center.
  • Página 5 All warranty requests or claims must be made no later than 60 days following the end of the 1-year warranty period. Repair or replacement shall be at the election and expense of Sioux Tools, and is the exclusive remedy in place of all other rights and remedies.
  • Página 6: Normas Generales De Seguridad

    INSTRUCCIONES Y PIEZAS PARA LOS MODELOS 8000ES, 8005ES, & 8050ES NORMAS GENERALES DE SEGURIDAD ¡ADVERTENCIA! Lea y comprenda todas las instrucciones. Si no sigue todas las instrucciones pueden producirse descargas eléctricas, fuego y/o lesiones personales graves. GUARDE ESTAS INSTRUCCIONES. ÁREA DE TRABAJO Mantenga el área de trabajo limpia y bien iluminada.
  • Página 7: Especificaciones

    “vivas” y el operador recibirá una descarga eléctrica. Mantenga una etiqueta de advertencia. SIMBOLOGÍA ESPECIFICACIONES Número de Voltios Broca helicoidal Doble aislamiento catálogo sin carga Capacidad en acero Canadian Standard Association 8000ES 0-1300 3/8" Underwriters Laboratories, Inc 8005ES 0-2500 3/8" 8050ES 0-750 1/2"...
  • Página 8 Cuando utilice brocas de perforación, inserte la broca lo suficiente para que las quijadas sujeten el vástago de la broca. Apriete las quijadas del portabrocas a mano para alinear la broca. Coloque la llave de apriete del portabrocas en cada uno de los tres agujeros del portabrocas, girándola hacia la derecha. Apriete lo suficiente.
  • Página 9: Mantenimiento

    Reparación de la herramienta Si la herramienta está dañada, envíe toda la herramienta al centro de mantenimiento autorizado de Sioux Tools más cercano. ACCESORIOS Los accesorios recomendados están disponibles con un costo adicional en su centro de mantenimiento local.
  • Página 10: Garantía De Herramientas Mecánicas

    60 días a partir del fin del período de 1 año de garantía. La reparación o sustitución debe ser a elección y cargo de Sioux Tools y es el remedio exclusivo que sustituye a todos los demás derechos y remedios.
  • Página 11: Consignes Générales De Mise En Garde

    INSTRUCTIONS & LISTE DE PIÈCES POUR 8000ES, 8005ES, & 8050ES CONSIGNES GÉNÉRALES DE MISE EN GARDE DANGER! Lisez attentivement toutes les consignes de mise en garde. Le non respect des consignes figurant ci-dessous expose l'utilisateur à un choc électrique, un incendie, et/ou des blessures corporelles graves.
  • Página 12 Entretenez les étiquettes de signalement de danger. SYMBOLES CARACTÉRISTIQUES Double isolation Volts Régime Capacité foret catalogue à vide hélicoïdal dans l'acier Ass. Canad. de Normalisation 8000ES 0-1300 3/8" Underwriters Laboratories, Inc 8005ES 0-2500 3/8" Underwriters Laboratories, Inc (Canada/United States) 8050ES 0-750 1/2"...
  • Página 13 Pour retirer le foret, introduisez la clé dans l'un des trous du mandrin et tournez-la dans le sens inverse des aiguilles d'une montre. DANGER! Pour prévenir les risques de blessures corporelles, retirez toujours la clé du mandrin après l'avoir utilisée. Retrait du mandrin Ouvrez les mâchoires du mandrin au maximum.
  • Página 14 à nouveau. N'utilisez pas d'outils endommagés. Posez une étiquette "NE PAS UTILISER" sur tout outil endommagé jusqu'à ce qu'il soit réparé. Réparation de l'outil Si votre outil est endommagé, retournez l'outil et ses accessoires auprès de votre centre de maintenance autorisé Sioux Tools le plus proche. ACCESSOIRES Les accessoires recommandés sont disponibles, moyennant supplément de coût, auprès de votre centre de maintenance le plus proche.
  • Página 15 OUTILS ÉLECTRIQUES PORTANT SA MARQUE SONT DÉPOURVUS DE TOUT DÉFAUT MATÉRIEL ET DE CONSTRUCTION. Pendant une durée d'un (1) an, à partir de la date d'acquisition, Sioux Tools s'engage à réparer ou remplacer, à sa discrétion, toute pièce présentant un défaut matériel ou de construction.
  • Página 16 14165 Chuck Shroud (8000ES, 8005ES) 68214 Armature (6 Tooth)(8000ES, 8005ES) 21131 3/8 Capacity Chuck (8000ES, 8005ES) 68258 Armature (4 Tooth)(8050ES) 22. 57250R Screw—M5 X .8 X 20 LH (8000ES, 8005ES) 68213 Field 35798 Washer (8050ES) 68159 Brush Set 68229 Chuck Shroud (8050ES)
  • Página 17 NOTES...
  • Página 18 NOTES...
  • Página 19 NOTES...
  • Página 20 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. El polvo generado al lijar, aserrar, afilar, taladrar y realizar otras tareas de construcción contiene sustancias químicas que podrían causar cáncer, malformaciones congénitas y otras alteraciones del aparato reproductor.

Este manual también es adecuado para:

8005es8050es

Tabla de contenido