Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
INSTRUCTIONS AND PARTS LIST FOR 1449HP, 1449HPB DRILLS
Read and understand "Safety Instructions For Air Tools" and these instructions before
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure
regulator, and lubricator will insure maximum output and life of tools. Before connecting tool, blow out the air line to remove water
and dirt which may have accumulated.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 3/8" (10mm) I.D. Extension hoses should be at least 1/2" (13mm) I.D. Use couplings and fittings
with at least 3/8" (10mm) I.D.
LUBRICATION
Use SIOUX No. 288 air motor oil. An airline lubricator, set to deliver 2 to 4 drops per minute, is recommended. If a lubricator is not
used, add .04 oz. (1.2cc, 12 to 15 drops) of oil into the air inlet twice daily.
Lubricate the gearing every 100 hours of operation with SIOUX No. 289A grease.
GENERAL OPERATION
This tool is equipped with a teasing throttle. By slightly depressing the trigger the chuck will rotate slowly. This is useful for
starting a drill bit without first spotting with a punch. The tool will run at maximum speed when the trigger is fully depressed.
If the gear case is removed or loosened, re-tighten to 35 ft-Ib.
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
September 1, 2003
Murphy, North Carolina, USA
Date and place of issues
(SERIAL "B")
operating this tool.
SOUND AND VIBRATION READINGS
*Sound Pressure *Sound Power
Catalog No.
dBA
1449HP
81.2
1449HPB
81.2
*per PN8NTC1
DECLARATION OF CONFORMITY
1449HP, 1449HPB
EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
Gerald E. Seebeck
President
Sioux Tools Inc.
Name and position of issuer
*Vibration
dBA
m/s
2
93.33
Less Than 2.5
93.33
Less Than 2.5
*per PN8NTC1
*per ISO 8662
Signature of issuer
1
Form ZCE456
Date 2003September4/A
Page 1 of 10
Printed In U.S.A.
Publicidad
Manuales relacionados para SIOUX 1449HP
Resumen de contenidos para SIOUX 1449HP
- Página 1 LUBRICATION Use SIOUX No. 288 air motor oil. An airline lubricator, set to deliver 2 to 4 drops per minute, is recommended. If a lubricator is not used, add .04 oz. (1.2cc, 12 to 15 drops) of oil into the air inlet twice daily.
-
Página 2: Allgemeiner Betrieb
*per ISO 8662 KONFORMITÄTSERKLÄRUNG Wir, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, erklären hiermit alleinverantwortlich, daß die Produkte 1449HP, 1449HPB auf die sich diese Erklärung bezieht, mit den Anforderungen der folgenden Standards oder Normen oder Dokumenten übereinstimmen: EN 792 (Entwurf) EN 292 Teile 1&2, ISO 8662, Pneurop PN8NTC1... - Página 3 LUBRICACION Utilice un aceite para motores neumáticos SIOUX No. 288. Se recomienda un lubricador de tubo de aire que distribuya de 2 a 4 gotas por minuto. Si no se utiliza un lubricador, agregue 0,04 oz. (1,2cc, 12 a15 gotas) de aceite a la entrada de aire, dos veces al día.
- Página 4 PN8NTC1 ISO 8662 CERTIFICAZIONE DI CONFORMITA La Sioux Tools, Inc, con sede al 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, solennemente dichiara sotto la propria e sola responsabilità che i prodotti 1449HP, 1449HPB sono conformi alle seguenti normative, standard o certificazioni:...
- Página 5 ISO 8662 DÉCLARATION DE CONFORMITÉ La société Sioux Tools, Inc., située à : 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, affirme que les produits 1449HP, 1449HPB visés par cette déclaration sont conformes aux normes ou aux documents normatifs suivants : EN 792 (version préliminaire), EN 292 Parties 1 et 2, ISO 8662, PNEUROP PN8NTC1...
- Página 6 PN8NTC1 ISO 8662 CONFORMITEITSVERKLARING Ondergetekende, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, verklaart met inachtneming van de eigen aansprakelijkheid desbetreffend, dat de produkten 1449HP, 1449HPB producten waarop deze verklaring van toepassing is, conform zijn met de hierna genoemde norm, normen en/of andere regels en voorschriften: EN 792 (voorstel), EN 292 onderdelen 1&2, ISO 8662, Pneurop PN8NTC1...
- Página 7 ISO 8662 FÖRSÄKRAN OM ÖVERENSSTÄMMELSE Vi, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, förklarar under eget ansvar att produkterna 1449HP, 1449HPB som denna försäkran gäller uppfyller följande standard eller standarder eller andra normgivande dokument:...
- Página 9 1449HP, 1449HPB DRILLS (SERIAL “B”) Fig. Part Fig. Part Description Description 21131 Chuck (3/8" Cap, 1/2-20 Th’d)(1449HP) 63192 Ass’y—Rotor Vane (Set of 5) 21133 Chuck (3/8" Cap, 3/8-24 Th’d) 10554 End Plate—Rear (1449HP Old Units) 10230 Bearing—Ball 30002 Key—Chuck (3/8" Chuck) 21491 Ring—Retainer...
- Página 10 Printed In U.S.A.