1449ESR, 1450ESR, 1451ESR, 1452ESR, 1454ESR, 1455ESR, 1456ESR DRILLS
Read and understand these instructions before operating this tool.
Everyone using, maintaining, changing accessories or working near this tool must read, understand and follow these Safety Instructions!
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator, and lubricator
will insure maximum output and life of tools. Before connecting tool, blow out the air line to remove water and dirt which may have accumulated.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 3/8" (10mm) I.D. Extension hoses should be at least 1/2" (13mm) I.D. Use couplings and fittings with at least 3/8"
(10mm) I.D.
LUBRICATION
Use SIOUX No. 288 air motor oil. An airline lubricator, set to deliver 2 to 4 drops per minute, is recommended. If a lubricator is not used, add .04 oz. (1.2cc,
12 to 15 drops) of oil into the air inlet twice daily.
Lubricate the gearing every 100 hours of operation with SIOUX No. 289A grease.
GENERAL OPERATION
This tool is equipped with a teasing throttle. By slightly depressing the trigger the chuck will rotate slowly. This is useful for starting a drill bit without first
spotting with a punch. The tool will run at maximum speed when the trigger is fully depressed.
If the gear case is removed or loosened, re-tighten to 35 ft-Ib.
On reversing tools, the direction of spindle rotation is controlled by the reversing button. When the button is depressed, the spindle rotates
counterclockwise. Always depress the button fully to obtain full power. The reversing button on some models can be locked in the reverse
direction by fully depressing and rotating the button clockwise.
Catalog No.
1449ESR
1450ESR
1451ESR
1452ESR
1454ESR
1455ESR
1456ESR
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
January 1, 2004
Murphy, North Carolina, USA
Date and place of issues
250 Snap-on Drive • PO Box 1596 • Murphy, NC 28906 • USA • Phone: 828-835-9765 •www.siouxtools.com
Form ZCE588C
INSTRUCTIONS AND PARTS LIST FOR
(SERIAL "C")
SAVE THESE INSTRUCTIONS!
WARNING
When used improperly power tools can create hazardous situations.
Improperly used power tools can cause injury or death.
SOUND AND VIBRATION READINGS
*Sound Pressure dBA
78.0
78.0
78.0
78.0
78.0
78.0
78.0
*per PN8NTC1
DECLARATION OF CONFORMITY
1449ESR, 1450ESR, 1451ESR, 1452ESR, 1454ESR, 1455ESR, 1456ESR
EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
Gerald E. Seebeck
Sioux Tools Inc.
Name and position of issuer
Original
Instructions
*Sound Power dBA
90.0
90.0
90.0
90.0
90.0
90.0
90.0
*per PN8NTC1
President
1
Form ZCE588C
Date 2004January22/A
Page 1 of 10
*Vibrationm/s
2
Less than 2.5
Less than 2.5
Less than 2.5
Less than 2.5
Less than 2.5
Less than 2.5
Less than 2.5
*per ISO 8662
Signature of issuer
2004January22/A
Date