Cequent Performance Products 51095 Instrucciones De Instalación

Truck frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51095F
Wrenches: 3/4", 7/8"
Drill Bits: None
Blocks
Hitch
SuperDuty's
Light Duty's
Figure 2.
Bottom view of hitch showing
correct block orientation
1/2"-13 X 1-3/4" Carriage Bolt
Qty. (6)
1
1/4" x 1-1/2" x 2" Carriage blocks with square hole
Qty. (6)
2
1/4" x 1-1/2" x 2" Blocks with round offset hole
Qty. (4)
3
Before installing hitch lower spare tire on all SuperDuty trucks. Lower spare tire on all Light Duty trucks with 16" or larger tires.
1.
Spare will be relocated or reinstalled after hitch installation.
Note! - 20" spare tires will not allow original relocation under truck. Also see Note and
2. As shown in Figure 2 above SuperDuty trucks will use the outer most hole and Light Duty trucks will use the inner most hole on
the hitch frame brackets. Make sure that no electrical wires or other obstructions are inside of truck frame so that bolts and
blocks can sit flat on bottom of frame when tightened in the following steps.
3. Install bolts and blocks down through truck frame as shown in Figure 1. Raise hitch into position carefully so as not to push
bolts back through frame. Install blocks, lockwashers and nuts making sure to orient blocks as shown in Figure 2 depending on
model of truck. After insuring that blocks and bolts are sitting flat torque bolts to 75 Lb.-Ft. (102 N*M).
4. Relocate or reinstall spare tire. Note! Cequent Performance Products is not responsible for any spare tire or spare tire
hanger issues related to the installation of this hitch. We offer numerous custom designed hitches for these trucks; see
below.
--- See your local Draw-Tite, Hidden Hitch or Reese dealer for one of our custom fit hitches to allow the spare tire to relocate in
its original position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of
water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye
protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
z
2008, 2011, 2012 Cequent Performance Products
Installation Instructions
99-2007 Ford F250/350 Superduty Truck*
97-2003 Ford F150 & F250 LightDuty Truck*
2004 Ford F150 Heritage Truck*
*See notes below regarding spare tire
All Fasteners Typical
Both Sides
Truck frame
rail not shown
Driver's side
4
3
5
6
Tighten all 1/2-13 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU1, PU2 --- PU3 on 04' Heritage
1
2
1
2
Super Duty
Light Duty
Light Duty orientation
Super Duty orientation
1/4" x 1" x 2" Blocks with round hole.
Qty. (2)
4
1/2" Helical lock washers
Qty. (6)
5
1/2" Hex Nut
Qty. (6)
6
Sheet 1 of 3 51095N
Part Numbers:
51095
97095
Max Gross Max Tongue
Trailer WT (LB) WT (LB)
10,000 (4540 Kg) 1000 (454 Kg)
6000 (2724 Kg) 600 (272 Kg)
Passenger's side
truck frame rail
1
2
Figure 1.
Star below.
2-1-12
Form: F205 Rev A 5-6-05
Rev. C