Connection/Operation; Heating On/Off - Grasslin thermio Serie Instrucciones De Montaje

GB Assembly/Installation
Lift the adjusting knob with a suitable tool
1
2 Release the fastening screw
3 Remove the upper part of the case
4 Determine the appropriate type of installation
5 – The unit must be connected by a qualified person exercising
due care
– Switch off the heating system before assembly
– Check and make sure that the connecting wires are not
live
GB

Connection/Operation

6 Determine the temperature range
Put the setting knob on the shaf. Note the markings!
7
8 thermio 102
a) –
b) –
c)
d) C
–
Technical data
GB
thermio 102
Dimensions H x W x D mm 75 x 71 x 21
Weight g (approx.)
Connection 2-wire
Power consumption approx. 200 mW
Switching capacity
- with ohmic load 0,5/5 A/250 V~
0,5/4 A/250 V~
- with inductive load cos. ϕ 0,6
- minimum 0,5/1 A/24 V–
Switching output Opens (with increasing temperature)
Ag Ni
Switching contact
Ambient temperature T 30
II after suitable installation
Protection class
Switching status indication –
- thermostat –
–
- selector switch
Type of installation Surface mounting
Type of connection Screw terminal with wire fuse
Day temperature regulation range +5 °C to +30 °C
Overnight temperature drop –
approx. 1 K
Temperature switching differential
Feedback Thermal
Storage temperature -20 °C to +70 °C
Type of protection IP 20
Radio interference suppression as per EN 55014
thermio 402 thermio 103
–
1 = Heating ON
0 = Heating OFF
S e t t e m
o n n e c t i o n
– Connect terminal 3
Lower temperature ON
Set the room temperature
Lower temperature OFF
Set the room temperature
thermio 402
75 x 71 x 21
2-wire
approx. 200 mW
0,5/5 A/250 V~
0,5/4 A/250 V~
0,5/1 A/24 V–
Opens (with increasing temperature)
Ag Ni
T 30
II after suitable installation
yes
–

Heating On/Off

Surface mounting
Screw terminal with wire fuse
+5 °C to +30 °C
–
approx. 1 K
Thermal
-20 °C to +70 °C
IP 20
as per EN 55014
Accuracy of control is only achieved if the stated current
values are adhered to.
Do you know how much current is drawn by the consumer?
If in doubt, check!
Select the right type of connection terminals when making the
connection!
– Guide the connecting wires through the opening in the unit's base
– Mount the base on a flat, firm surface or flush-mounted socket
– Strip the connection wires properly and connect as shown in
the circuit diagram, see the circuit diagrams on the following
pages
thermio 403
– –
1 = Heating ON
–
0 = Heating OFF
p e r a t u r e
o f a t i m
–
e. g. 22 °C
ON
18 °C
= ^
e. g. 22 °C
OFF
22 °C
= ^
* Lower temperature = Comfort temperature minus 4 K (Kelvin)
thermio 103 thermio 403
75 x 71 x 21 75 x 71 x 21
3-wire 3-wire
approx. 200 mW approx. 200 mW
10 A/250 V~ 10 A/250 V~
4 A/250 V~ 4 A/250 V~
0,1 A/230 V– 0,1 A/230 V–
Opens (with increasing temperature) Opens (with increasing temperature)
Ag Ni Ag Ni
T 30 T 30
II after suitable installation II after suitable installation
– yes
– –
– Heating On/Off
Surface mounting Surface mounting
Screw terminal with wire fuse Screw terminal with wire fuse
+5 °C to +30 °C +5 °C to +30 °C
approx. 4 K –
approx. 0,5 K approx. 0,5 K
Thermal Thermal
-20 °C to +70 °C -20 °C to +70 °C
IP 20 IP 20
as per EN 55014 as per EN 55014
thermio 513
LED OFF = Comfort temperature
LED ON = Lower temperature
2 = Comfort temperature
1 = Lower temperature
v a l u e
e s w i t c h
Connect terminal 3
Lower temperature ON
Set the room temperature
e. g.22 °C
ON
LED ON +
^
=
Lower temperature OFF
Set the room temperature
e. g.22 °C
LED OFF + OFF
= ^
ON
LED OFF +
^
=
thermio 513
75 x 71 x 21
3-wire
approx. 200 mW
10 A/250 V~
4 A/250 V~
0,1 A/230 V–
Opens (with increasing temperature)
Ag Ni
T 30
II after suitable installation
yes
LED green
Overnight temperature drop On/Off
Surface mounting
Screw terminal with wire fuse
+5 °C to +30 °C
approx. 4 K
approx. 0,5 K
Thermal
-20 °C to +70 °C
IP 20
as per EN 55014
18 °C
22 °C
22 °C