Before Use - Miniland digital camera 2.4 Manual De Instrucciones

ENGLISH
· Reorient or change the position receiver.
· Increase the distance between the equipment in
question and the baby monitor.
· Connect the equipment to a different socket from
that used for the receiver.
· Consult the Customer Care department.
To ensure compliance with the R&TTE Directive
1999/5/EC, this equipment has special shielded
cables. Operating
or using unshielded cables will probably cause
interference to radio or TV reception.
3.3. CHOOSING THE RIGHT PLACE
· Place the electronic device somewhere out of the
reach of children so as to avoid accidents.
· The baby unit must be situated at least 1 and 1.5
metres away from the baby's cot. Never place the
baby unit inside the cot, bed or playpen, nor secure
the tripod to them. Make sure that the unit, the cables
and the adapter are well out of the reach of the baby
and other young children.
· Put the baby monitor in a place where the air can
circulate freely. Do not place it on duvets or soft
blankets nor in the corners of cupboards, shelves etc.
· Place the baby monitor well away from heat sources
like radiators, chimneys, kitchens and direct sunlight.
· Keep the Camera away from TV appliances,
repeaters and radios. The intense radio signals
generated by these elements could cause noise
or even sounds or images to be broadcast on
the monitor. Should this occur, move the camera
somewhere else.
4. PRODUCT FEATURES
4.1. MONITOR FUNCTIONS AND CONTROLS
MONITOR
1. Charging LED
2. Power LED
3. Volume LEDs
4. LCD Screen
5. Menu/Back key
6. Nav UP & Vol up key
7. Nav RIGHT & Zoom key
8. Feeding Alert
9. Nav LEFT & Brightness key
10. Nav DOWN & Vol. Down key
11. Medicine Alert
12. Power button
13. Talk to the baby key
14. Confirmation key
15. Diaper Alert
16. Sleeping Alert
17. Microphone
18. Spaker
19. Micro USB DC Jack
20. Stand
DISPLAY
A) Signal level
B) Volume
C) Night vision
D) Zoom
E) Lullabies
F) Vox Mode
G) Selected camera
with unapproved equipment
H) Battery level
I) Feeding alarm
J) Medicine alarm
K) Diaper alarm
L) Sleeping alarm
M) Date&Time
N) Locked touch panel indicator
O) Talk to the baby activated indicator
4.2. CAMERA FUNCTIONS AND CONTROLS
I. Retractable antenna
II. Photo sensor
III. Power button
IV. Hanging attachment
V. Speaker
VI. Link button
VII. Mini USB power connector
VIII. Microphone
IX. ON/link LED
X. Camera lens
XI. Infrared
XII. Tripod attachment
5. INSTRUCTIONS FOR USE

5.1. BEFORE USE

5.1.1. CAMERA POWER SUPPLY
The camera or baby unit of this baby monitor is
designed for use with the AC/DC adapter supplied.
1. Place the connector socket (VII) at the rear of the
baby unit.
2. Connect the adapter cable to the mini-USB socket
of the camera. Only use the adapter supplied.
3. Plug in the adapter to the mains.
Warning: Danger of Strangulation – Keep the
cable out of reach of the baby. NEVER place a
camera with cables less than 1 metre away from
the cot. Never use extension cables with AC
adapters. Only use the AC adapters supplied
5.2. OPERATION
5.2.1. TURNING THE CAMERA ON/OFF
To turn the camera on or off, keep the on button (III)
pressed in for two seconds. The ON/link LED (IX) will
go on and off depending on whether you turn the unit
on or off.
When you have installed the camera and turned it
on, you can see the images and listen to the sounds
captured in your baby's room via the monitor.
Remember that to see the image of this camera on
your monitor you must first pair the units following the
instructions shown in section 5.2.6.
5.2.2. INFRARED NIGHT VISION (AUTOMATIC)
The infrared night vision function allows the camera to
pick up images of your baby or the monitored area in
dark or low light conditions.
In this mode, only black and white images will be
displayed on the monitor and only objects located less
than 2 meters away can be seen.
The camera constantly monitors the light level and
automatically changes to infrared mode when there is
insufficient light for normal vision.
10