Nolan N83 Seguridad E Instrucciones página 5

INSTRUCTIONS FOR USE
• VISOR
1 Disassembly
1.1 Pull the visor fully up.
1.2 Push the visor release button (A) and hold it down. Slide the visor forwards to the release position
(Fig. 1).
1.3 Release the visor fastenings (B1 and B2).
1.4 Repeat the operations above on the other side of the helmet.
WARNING!!!
- After assembly and disassembly of visor parts pull the visor up and down to check that the mech-
anism is working correctly; if necessary repeat the operations above.
- Do not remove the mechanisms for pulling the visor up and down from the shell.
- If the mechanisms for pulling the visor up and down are damaged or faulty please contact an
authorised Nolan dealer.
2 Assembly
2.1 Pull the visor up and align the fastenings (B1 and B2) with the corresponding housings on the visor
mechanism (Fig. 2).
2.2 Insert fastening B1 into the corresponding housing and press the visor against the shell in align-
ment with fastening B2. This will activate the visor release button (Fig. 2).
2.3 Slide the visor until the visor lock system locks
2.4 Repeat the operations above on the other side of the helmet.
• REMOVABLE & WASHABLE COMFORT PADDING
(Only for the versions equipped whit removable interior)
1 EXTRACTION
1.1 Undo the chin strap (see relevant instructions), then remove the left cheek pads by pulling its front
end towards the inside of the helmet, to snap open the buttons on the pad rear end. Repeat the
same operations for the right cheek pad (Fig. 3).
1.2 To remove the left cheek pad release the left chin strap padding from its slot in the cheek pad
(Fig. 4); repeat the same operations for the right chin strap padding.
1.3 Release the rear fixing flap on the left-hand side from its support in the inner shell, by gently
working the shell edge seal and pulling the comfort padding at the nape height towards the inside
(Fig. 5). Then do the same for the central flap and the rear right-hand flap.
1.4 Release the front fixing flap on the left-hand side from its support in the inner shell, by gently
pulling the comfort padding towards the inside of the helmet (Fig. 6). Then do the same for the
central flap and the front right-hand flap.
1.5 Extract the comfort padding from the helmet inside.
2 FITTING
2.1 Correctly insert the inner padding into the helmet.
2.2 Insert the fixing front flaps into the shell support, by gently pushing the liner towards the helmet
outside (Fig. 6).
2.3 Insert the left- front- and right-hand padding rear flaps in the special support in the nape area
(Fig. 5). To do this, gently work the shell edge seal and push until you hear the locks go click, tak-
ing care to spread the liner in such a way that it adheres to the internal polystyrene.
2.4 Insert the band and the left chin strap in the special slot of the left cheek pad (Fig. 4).
2.5 Insert the left-hand cheek padding rear flaps between the outer and the inner shells by gently
pushing towards the helmet back. Then press the cheek pad front to snap close the buttons on
the pad rear end (Fig. 3). Repeat 2.4 and 2.5 operations for the right-hand cheek pad.
8
WARNING!!!
- Take out the inner padding only to clean and wash it.
- Never use your helmet without having correctly and completely replaced the inner comfort padding
as well as the cheek pads.
- Do not machine wash.
- Never use any tools to carry out the above-described operations.
• NFRS - NOLAN FOG RESISTANT SYSTEM
Pinlock ®
(uses the patent licence of )
1 INNER VISOR ASSEMBLY
1.1 Remove the visor.
1.2 Remove the protective film from the inner visor on the face in contact with the visor.
1.3 Check the inner surface of the visor is clean.
Attention: the presence of dust between the visors can produce scratches on both surfaces.
1.4 Rest one side of the inner visor on one of the visor pins and hold it in position (Fig. 7).
1.5 Open the visor and fasten the other side of the inner visor to the second pin (Fig. 8).
1.6 Release the visor.
1.7 Remove the second protective film from the inner visor.
ATTENTION!!!
- Check that both visors are tightly connected and do not move; if they do, adjust the spring
pins using a screwdriver to set the adherence (Fig. 9).
1.8 Fit the visor in the helmet.
ATTENTION!!!
- Make sure that the system has been assembled properly by pulling up and down the visor.
- Scratched visors and inner visors can cause reduced visibility and must therefore be
changed.
2 DISASSEMBLY
2.1 Remove the visor equipped with inner visor.
2.2 Widen the visor: the inner visor will come off automatically.
• WIND PROTECTOR / BREATH DEFLECTOR
These accessories allow to improve the helmet performances in particular use conditions.
The wind protector prevents annoying air infiltration from the chin area (see Fig. 10 for assembly and
disassembly).
The breath deflector prevents the visor misting by diverting the breath flow downward (see Fig. 11 for
assembly and disassembly).
ATTENTION!!!
The wind protector and breath deflector are easily removable. The correct assembling of these acces-
sories can be checked by pulling them slightly with your thumb and forefinger. If they move, then repeat
the assembling operations.
• NOISE REDUCER
The cheek pads are ready, in the auricular area, for the insertion of NOISE REDUCER plugs (standard
supplied) that can be easily pressure-inserted or removed (velcro), leaving the ear free (Fig. 12).
9