Cequent Performance Products 45299 Instrucciones De Instalación

!
NOTE;
WITH THIS HITCH INSTALLED
THE STEP BUMPER IS NO LONGER ABLE
TO BE USED AS A TOWING POINT.
Hitch Shown In Proper Position
Equipment Required: WOOD BLOCKS
Fastener Kit: 45299F
Wrenches: m16,m18,m21, 3/8"
Drill Bits: 9/16"
EXISTING
M14 BOLTS
2010 MODEL
EXISTING
BUMPER
CORNER
BRACE
BUMPER BUMPER
ATTACHMENT
(NOT REQUIRED ON 03-09)
2010 – CURRENT
MODEL
ATTACHMENT
EXISTING M14 HANDLE NUT (03-09 MODEL)
M14 FLANGED NUT (2010 MODEL)
1 1
Qt Qty. (4) (4) HEX NUT – M14 X 2.00 HEX NUT
2
Qty. (4) CONICAL WASHER – 5/8"
3
Qty. (6) HEX NUT – M12 X 1.75
4
Qty. (14) CONICAL WASHER – 1/2"
5
Qty. (4) CARRIAGE BOLT – 1/2"-13 X 1-3/4" GR 8
Tighten M12 hitch fasteners with torque wrench to 75 Lb -Ft (102 N*M) Tighten M12 hitch fasteners with torque wrench to 75 Lb.-Ft. (102 N M)
Tighten M14 and 1/2" fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry
of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and
wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE
J684.
z
2010 Cequent Performance Products
Installation Instructions
Dodge 2500/3500 Pickup
Bumper
BED ATTACHMENT BED ATTACHMENT
HOLE
#4
9
4 4
10
CENTER BUMPER
ATTACHMENT
VIBRATION DAMPENER
(ON CERTAIN MODELS ONLY)
FIGURE 1
M14 X 2 00
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or Manufacturer s Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
LONG BED
FRAME
#3
DRILL ONE HOLE
2 1
3 3
4
TOP HOLE – BUMPER
ATTACHMENT
6 6
Qt Qty. (2) (2) BLOCK BLOCK – 1-1/2 X 3-1/2 X 1/4"
7
Qty. (4) HEX NUT – ½-13 GR 2H
8
Qty. (2) FISH WIRE – 1/2"
9
Qty. (4) HEX BOLT – M12 X 1.75 X 45mm CL 10.9
Qty. (3) BLOCK – SPACER 1/2 X 1-1/2 X 5-3/4
10
Tighten M12 bed fasteners with torque wrench to 85 Lb.-Ft. (115 N M) Tighten M12 bed fasteners with torque wrench to 85 Lb Ft (115 N*M)
Tighten all M10 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Sheet 1 of 6 45299N
Part Numbers:
45299
Max Gross
Trailer WT (LB)
18000 (8172 kg)
18000 (8172kg)
Wiring Access Location: PU3, PU4
5
6
4
7
2003-09 MODEL
ATTACHMENT
1 1/2 X 3 1/2 X 1/4"
2-15-10
Form: F205 Rev A 5-6-05
Max Tongue
WT (LB)
2500 (1135 kg)
2000 (908 kg)
SHORT BED
FRAME
DRILL 2
HOLES
03-09 MODEL
EXISTING
BUMPER
CORNER
BRACE
EXISTING
M12 BOLTS
Rev. A