Hoover HVI 640 Manual De Instrucciones página 6

• FAST HEATER OPERATION
All zones are fitted with a "Fast heater" which allows to get a faster
temperature increase of the heating areas. Ideal to seal meat or
to bring quickly to the boil large quantitites of liquids.
Starting the fast heater
. Press the on/off button
. Start the required zone, press the + button to obtain position "9",
release the button briefly and press it again; the display alternates
showing "A" (fast heater) and "9" (heat level).
. If necessary choose the required heat position.
Cooking Power released
position %
0
U
1
2
3
4
5
6
7
8
9
E.g. 1800 W zone at position 6 = 32% of 1800 W power
released = 576W
When the "Fast heater" is on, the zone supplies 1800 W
power for 2.5 minutes, and adjusts to 576 W after this time.
. When the "Fast heater" is done, the display of the power level
remains steady.
• ACTIVATION OF THE BOOSTER FUNCTION
The booster function allows to get by a simple pressure the
cooking zone working with a high power according to the zone,
for 10 minutes period.
Ideal to bring to the boil large quantities of liquids ...
Activation of the BOOSTER function :
- Press the setting key of the cooking zone fitted
with the booster function.
The control led is displayed.
- Press the key to start the Booster.
The Booster is active for 10 minutes.
The P mark (power) appears.
When the time is over, the power level decreases to 9.
A pressure on the key "-" cancels the booster function, and the
power level decreases to 9.
.
Time of fast
heater minutes
0 0
(65°C) -
3 1
6 3
11 5
16 6,5
19 8,5
32 2,5
45 3,5
65 4,5
100 0
• PROGRAMMING A COOKING ZONE
Every cooking zone can be programmed for a maximum time of
99 minutes. Only one zone, at a time, can be programmed.
- Start the required zone by following the previous instructions.
The control LED near the heat level must be displayed, it shows
that the zone is live.
- Press the Timer button
The zone mark around the timer display shows the controlled
zone.
- Press the or - button to select the time in minutes.
This is saved automatically after three seconds.
The programmed time can be modified at any moment by pressing
the timer selection button, the timer control LED must be on.
When the time has run, the cooking zone goes off automatically
and an audible beep sounds for 1 minute. Press the timer
button to stop it.
The programmed time can be reset to
or pressing the and
zone is then no longer linked to the timer but stays operational.
So you will have to stop the zone independently.
The timer can be used alone as a reminder, it will ring at the end
of the programmed time.
• LOCKING BUTTON OPERATION
The locking function holds the current settings, or prevents anyone
from starting the hob. It is also used for cleaning the control strip
as the controls can be locked without the hob being on.
To lock :
- Press the on/off button
- Start the required cooking zones.
- Select a heat level for each of them;
- Press the button to set the data ; in this way no other button
works, except the on/off button.
The locking indicator lamp comes on.
To unlock :
To release the locking function just press the
indicator lamp goes off, all the controls work again.
If when the controls are locked, the timer is on, the time will be
counted automatically and the zone switched off at the end of the
programmed time.
If the locking control is on when the hob is finally shut down,
the locking control stays operational and prevents any action
when the hob is restarted, press the
locking function.
5 GB
.
using the
buttons at the same time, the cooking
.
button ; the
button to release the
button