Publicidad
General
Tiger washbasin taps are designed for installation on on washbasins with a tap opening of 30 - 37 mm (accor-
ding to NEN-EN 32). Type 5025.8 is suitable for mounting on washbasins or washtops with recessed washbasins.
Type 5025.9 is suitable for mounting on washtops with high or raised washbasins.
Ontario washbasin tap assembly instructions
Installation:
(see accompanying drawings) Before you start: Flush the pipes thoroughly in order to make sure there that no dirt
can get into the tap from the pipes. The warranty does not cover damage to interior parts as a result of dirt.
1.
Your Ontario washbasin tap tap features a 'Top fixing' system. This means that installation above the
hand basin requires no special tools. Check whether the assembly unit is put together properly by
comparing it with the drawing. The markings should always be facing outward during assembly.
2.
Push the bottom plate through the hole in the sink by bending the flexible help strips somewhat.
3.
Hold onto both help strips and slide the top plate together with the flexible sealing washer.
4.
Insert the three assembly bolts (included) and tighten these firmly and evenly.
5.
Check whether the assembly plate is mounted straight with the marking on the front. Snip or slice the
help strips off. Any parts of the gasket protruding from the upper assembly plate must be cut off.
6
Type 5025.9: push the flexible pressure hoses through the opening in the base. The marking
on the mounting ring must always be placed at the front. Fix the tap to the base by firmly tightening the
mounting screw at the rear of the tap.
7.
Push the flexible pressure hose through the opening of the assembly unit and put the tap on the
washbasin.
8.
Attach the tap to the assembly unit by firmly tightening the assembly screw on the back.
Connect the feed hoses to your water mains using compression fittings (not supplied). Red (right)
is hot, blue (left) is cold. The pressure hose has a diameter of 10 mm. The connection to the
water mains differs for each house. Compression bushes are available from your dealer (article
number 4550.3.55.41, 2 pieces) to connect to a stopcock with a 3/8 threaded connection.
9.
Operation: if the handle is in the vertical position the water supply will be cut off. You can open
the water supply by moving the handle outwards. Control the volume of the water jet by moving the
handle outwards more or less. Water temperature can be controlled by moving the handle forwards
or backwards; backwards for hot, forwards for cold. Both settings can be controlled at the same time.
Turn on the water pressure and check for leaks. Tiger disclaims any and all liability for damage caused by impro-
per use. Your tap is now ready to use.
Features:
Your washbasin tap features:
•
'Top fixing' assembly system. The tap is installed from the top, without the need for any special tools
•
Ceramic discs
•
Solid brass housing and handle
•
Easy control of temperature and water flow with one hand
•
PEX flexible pressure hoses (a standard feature for use in drinking water units under the new
international standard)
•
Regulated aerator with anti-limescale function, independent of pressure
Maintenance:
Clean with a soft, damp cloth; do not use any abrasives. The warranty does not cover damage caused by insuf-
ficient or improper maintenance, the use of aggressive abrasives, scratches, negligence, normal wear and tear or
changes to the structure made by non-qualified persons.
Anti-calcium aerator: Remove the calcium deposits by rubbing firmly with your fingertips across the outlet (aerator)
of the tap. Thanks to its special design and flexible material, this should be enough to restore the high-perfor-
mance action of the aerator.
Service and warranty:
Tiger guarantees that your washbasin tap will work perfectly. However, should there be any problem with your tap
resulting from any production and/or material error, Tiger will replace the defective part(s) free of charge within
the 5 year warranty period. If the tap cannot be repaired, you may claim a replacement product under the war-
ranty. Your proof is purchase is also your warranty, and should be submitted when making any warranty claims.
The drawing on page 11 contains an overview of all of the parts and the corresponding article numbers.
-2-
5000.5.03.33
5000.5.03.01
(3pcs)
C B
A
5000.5.07.51
5000.5.01.10
(2pcs)
5000.5.80.51
Ø10
Ø10
5000.5.03.99
( 1pcs)
10.
service parts
Ø10
3/8
art. nr. 4550.3.55.4
3/8 x 10 (2pcs)
-11-
5000.5.03.53
5000.4.05.92
5029.0.03.20
FRONT
5000.5.03.52
5029.0.03.10
5029.5.00.12
5029.0.07.35
5000.3.03.92
1.
2.
5029.5.03.75
5000.5.03.53
3.
4.
-12-
5.
6.
7.
8.
-13-
Publicidad
