Code Entry - THOMSON ROC130 Manual De Instrucciones

ROC130 7/05/99 20:02
This Universal Remote Control is compatible with most models of infrared-controlled TV sets
manufactured after 1993 and supporting the functions Pr+ and Pr-.
It was factory-programmed to control the TV sets manufactured by the THOMSON group.
Please keep this guide along with the code list (provided separately), so that you can
subsequently programme your remote control for use with other sets.
When you have loaded the batteries, please switch on your TV set manually and then try to
switch it off with the remote control. Should the TV set not respond, you'll have to enter one
of the codes contained in the list supplied separately (the most often used codes are to be
found at the top of the list). To do so, proceed as per the following procedure.
1
The red indicator lamp lights up when you press any key.
2
B B : to switch the TV set on or on standby.
3
volume +/- and program.
4
: mute and sound reactivation.
Direct code input
To directly input the code read from the list:
1. Switch your TV set on.
2. On page 1 of the separate code list enclosed, find the codes matching the make of the TV set which you want
to control.
3. Hold down keys mute
4. While the indicator lamp is on, with the keys (3) program.
volume+ (3rd number), enter the 3-digit code.
EXAMPLE: To enter code 027, do not press the key program.
seven times. The red indicator lamp (1) flashes whenever a key is pressed.
5. To save the code, press key
the list, the red indicator lamp flashes rapidly during 3 seconds and then goes off.
6. Code check: Direct the remote control towards the TV set and try to switch it over to standby by simply pressing
the key B B .
Automatic code retrieval
1. Switch your TV set on.
2. Hold down keys mute
3. Direct the remote control towards the TV set and try to switch it off by simply pressing the key B
set not switch off, press B
subsequent key depressions, give the red indicator lamp (1) enough time to extinguish and light up again (about
1 second). Proceeding this way will enable you to see whether the set responds or not.
4. Immediately after the TV set switches over to standby, press key
lamp (1) goes off.
Retrieval of the code stored in your remote control
To retrieve the code stored in your remote control:
1. Hold down keys
mute
2. Press key volume-.
3. To visualise the first code digit, press program.
The digit "0" does not generate any flash pulse.
4. For the second code digit, press key program.
5. For the third code digit, press key volume+ and count the flash pulses of the red indicator lamp (1). The indicator
lamp extinguishes after the last flash.
NOTE: The default code 165 stored in the remote control works with most of the TV sets of the THOMSON make and
with some models of the makes Saba, Brandt, Ferguson, Nordmende and Telefunken.
Page 1
Description of the key functions
∧ ∨
/ : to adjust the volume and to change the channel.

Code entry

(4) and B B (2) until the red indicator lamp (1) remains lit.
(4) The red indicator lamp (1) goes off. Should the code entered not be on
mute
(4) and B B (2) until the red indicator lamp (1) remains lit.
B (2) as many times as required (up to 200 times), until the set switches off. Between two
(4) and B B (2) until the red indicator lamp (1) remains lit.
When you have retrieved the code of your set,
jot it down so that you can use it whenever needed.
∧
(1st number), program.
∧
, press program.
to store the programming. The red indicator
mute
∧
and count the flash pulses of the red indicator lamp (1).
∨
and count the flash pulses of the red indicator lamp (1).
1
∨
(2nd number) and
∨
twice and volume+
B (2). Should the
TV CODE