GB
ried out by KETTLER service staff or qualified personnel trained
by KETTLER.
■
In case of enquiry, please contact your KETTLER dealer.
■
In choosing the location of the apparatus, ensure a sufficient sa-
fety distance from any obstacles. The apparatus must not be
Handling the equipment
■
Before using the equipment for exercise, check carefully to en-
sure that it has been correctly assembled.
■
Before beginning your first training session, familiarize yourself
thoroughly with all the functions and settings of the unit.
■
It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration
etc.). This may cause corrosion.
■
The machine is designed for use by adults and children should
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the ma-
nufacturer cannot be held liable. If, in spite of this, children are
allowed to use the equipment, ensure that they are instructed in
its proper use and supervised accordingly.
■
The crosstrainer complies with the DIN EN 957 -1/-9, class HB.
It is therefore unsuitable for therapeutic use.
■
A slight production of noise at the bearing of the centrifugal
mass is due to the construction and has no negative effect upon
operation. Possibly occurring noise during reverse pedalling re-
sult from engineering and are absolutely safe.
Instructions for Assembly
■
Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cau-
se for complaint, please contact your KETTLER dealer.
■
Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
■
The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if
possible technically talented.
■
Please note that there is always a danger of injury when wor-
king with tools or doing manual work. Therefore please be ca-
reful when assembling this machine.
■
Ensure that your working area is free of possible sources of
danger, for example don't leave any tools lying around. Al-
ways dispose packaging material in such a way that it may not
cause any danger. There is always a risk of suffocation if chil-
dren play with plastic bags!
List of spare parts page 24-25
When ordering spare parts, always state the full item no., spare-
partnumber, the quantity required and the S/N of the product
(see handling).
Example order: item no. 07645-000 / spare-part no. 68003250
/ 1 pieces / S/N ....................
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
should be clearly stated on the order by adding the words „with
fastening material".
4
mounted in the immediate vicinity of main passageways (paths,
doorways, corridors).
■
The product is not suitable for use by persons weighing over
110 kg.
■
Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the
environment.
■
The crosstrainer has a magnetic brake system.
■
To operate correctly, the pulse function requires a minimum vol-
tage of 2,7 volts (only for computers working with batteries).
■
The equipment is dependent of revolutions per minute.
■
Please ensure that liquids or perspiration never enter the ma-
chine or the electronics.
■
Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.
■
Always wear suitable shoes when using.
■
All electric appliances emit electromagnetic radiation when in
operation. Please do not leave especially radiation-intensive
appliances (e.g. mobile telephones) directly next to the cockpit
or the electronic controlsystem as otherwise values displayed
might be distorted (e.g. pulse measurement.
■
The fastening material required for each assembly step is
shown in the diagram inset. Use the fastening material exactly
as instructed. The required tools are supplied with the equip-
ment.
■
Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand un-
til resistance is felt, then use spanner to finally tighten nuts com-
pletely against resistance (locking device). Then check that all
screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function correctly
(the locking device is destroyed), and must be replaced.
■
For technical reasons, we reserve the right to carry out preli-
minary assembly work (e.g. addition of tubing plugs).
■
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary. Goods may only
be returned after prior arrangement and in (internal) packa-
ging, which is safe for transportation, in the original box if pos-
sible. It is important to provide a detailed defect description /
damage report!
KETTLER GB Ltd. · KETTLER House, Merse Road · North
GB
Moons Moat · Redditch, Worcestershire B98 9HL
KETTLER International Inc. · 1355, London Bridge Road · VA
USA
23453, Virginia Beach
http://www.kettler.de