General Information; Operating Procedures - Telwin START PLUS 6824 Manual De Instrucciones

____________________(EN)____________________
INSTRUCTION MANUAL

GENERAL INFORMATION

A real, portable, battery-powered starter. Ideal for anyone
needing a starter. Its applications include boats, cars,
trucks, power generators, and yet more.
Fully compatible with any 12-volt or 24-volt starter system.
The Starter uses SEALED MAINTENANCE-FREE
BATTERIES (AGM) which means that the unit can be
installed in any position, in any location, without the fear
of any acid leaks.
Keep this manual.
The manual should be read, paying attention to all the
warnings and safety precautions to be taken when using
and maintaining the device, the list of components and all
technical specifications.
Please keep this manual in a secure and dry place for
future reference.
PLEASE READ ALL THE INSTRUCTIONS BEFORE
USING THE STARTER!
WARNINGS AND SAFETY PRECAUTIONS
Warning: in order to reduce the risk of personal injury
and damage to equipment, it is highly recommended
to comply with all essential safety measures and
precautions when using the starter.
1- Protect the eyes. Always wear protective
goggles when using acid lead accumulators.
2- Avoid contact with battery acid. If annul
operator should be sprayed or come into
contact with the acid, rinse the parts
immediately under clean running water. Continue to
rinse the area until the physician arrives.
3-
It is important to connect the cables with the
poles in the right direction. Connect the red
clamp (+) to the positive battery terminal,
and the black clamp (-) to the negative terminal.
Use the starter in well ventilated areas. Do not
attempt to use the starter when there is gas or
inflammable liquids in the vicinity.
4- Make sure that the black and red clamps
never come into contact or touch a common
conductor as this could cause them to fuse
together or with other metal objects.
WARNING! In order to prevent damage caused
by accidental contact, disconnect the mounting
socket (12V / 24V) from the starter panel and
place the clamps in the holder.
5- FOR 12 or 24 VOLT SYSTEMS ONLY! This device
is destined for use on embarkations and vehicles
running on 12 or 24 Volt electrical systems only.
6- USE ONLY IN EMERGENCIES: do not use the
starter instead of the vehicle battery. Use it during
start-up operations only.
7- Do not work alone. If there is an accident, the
assistant can be of assistance to the operator.
8-
Try to avoid electrical shocks. Be very
cautious when applying the clamps to non-
insulated conductors or bus bars. Avoid all
body contact with surfaces of tubes, radiators, and
metal power substations whilst testing the voltage.
9- Keep the work area clean at all times. Untidy
cumbersome areas can lead to injuries.
10- Protect the starter appropriately from all possible
damage. It must only be used as indicated in this
Instruction Manual.
11- Ensure compliance with the indications in the work
area. Do not use in humid or wet facilities. Never
leave it out in the rain. Always work in well lit areas.
12- Do not expose to direct sunlight, heat sources or
humidity.
13-
Keep out of children's reach: they must
never be allowed to access work areas or
handle any machines, tools or extensions.
14- When the starter is not being operated, it must be
stored in a dry area to prevent rust from forming.
Always store the starter under lock and key and keep
out of reach of children.
15-
moving parts. During all operations, the use of
electrically insulated protection clothing and non-slip
boots must be worn at all times. Persons with long
hair must wear a hair net.
16- Only experts are allowed to do repair work on the
machine as it involves significant risk levels for
inexperienced workers.
17- Replacing parts and accessories: when performing
maintenance operations, use identical spare parts
only (see Spare Part list). Use of any other spare
parts invalidates all warranties.
18- Make sure that the device is always positioned in a
stable and well supported manner.
Never climb over cables or electrical structures.
19- Careful attention must be paid when maintaining the
starter. Check the condition of cables on a regular
basis and if any damage is detected, have the same
repaired by an authorised technician.
20- Check there are no damaged parts. Before using this
starter, carefully check all seemingly damaged parts
and assess whether or not they can operate correctly.
Check that the cables are securely fastened to the
starter. Remember that only qualified technicians are
allowed to repair or replace damaged parts.
INSTALLATION
ASSEMBLY (Fig. C)
Unpack the starter and assemble the separate parts
included in the package.

OPERATING PROCEDURES

WARNING: Electric shocks may cause
injury or death. Do not touch bare
electrical conductors.
The starter is designed for use on vehicles or boats. It
does not need another vehicle or a 230V AC power
supply socket.
This starter can also be used as a portable, 12V DC,
power supply for remote areas or in emergencies.
Using the starter to start a vehicle
WARNING:
meticulously, and always in the order given
below!
- Check that the starter clamps are NOT powered up: the
mounting socket (Fig. A-1) must be disconnected.
- Make sure that the vehicle or boat to be started is
switched off - switch or ignition key in the OFF position.
- First connect the red clamp to the positive terminal on
the vehicle battery.
- Then connect the black clamp to a non-movable metal
part of the engine; do not connect the clamp to the
negative terminal on the battery.
3
Always wear suitable
Never wear baggy clothing or
jewellery that can get caught up in
follow these
clothing.
instructions