Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 87186F
Wrenches: 3/4 , 21 mm
Drill Bits: None
Frame
1
Qty. (4)
Carriage Bolt 1/2-13 X 1-3/4
2
Qty. (4)
Spacer
Fasteners Typical Both Sides of Vehicle
Note: Factory Installed Steel Step Bumper and Brackets Must Be Used In Conjunction with Hitch
1. Remove existing M14 bolts from end of each frame rail.
2. Lift receiver into position, locating rearmost slots in receiver under existing weldnuts in vehicle frame.
3. Reinstall existing M14 bolts through receiver and frame into existing weldnuts.
4. Install remaining fasteners as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2006 Cequent Towing Products
Installation Instructions
Chevrolet Silverado Pickup
GMC Sierra Pickup
(Requires OEM Bumper)
Note: Factory Installed Steel Step Bumper
and Brackets Must Be Used In
Conjunction with Hitch
Tighten M14 CL10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
1
Ball Mount
2
Wiring Access Location: PU3
Factory installed bumper bracket
- Typical both sides
Existing weldnut typical both sides
3
4
Existing M14 bolt
Note: All Fasteners Typical Both Sides of Vehicle
3
Qty. (4)
Conical Washer 1/2
4
Qty. (4)
Hex Nut 1/2-13
Sheet 1 of 3
87186N
Part Numbers:
87186
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
8000 (3632 Kg)
800 (363 Kg)
6000 (2724 Kg)
600 (272 Kg)
5-18-06
Rev. B
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Towing Products 87186
Resumen de contenidos para Cequent Towing Products 87186
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2006 Cequent Towing Products Sheet 1 of 3 87186N 5-18-06 Rev.
- Página 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2005, 2006 Cequent Towing Products Feuille 2 de 3 87186N 5-18-06 Rev.
- Página 3 No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. 2005, 2006 Cequent Towing Products Hoja 3 de 3 87186N 5-18-06 Rev.